Publicité
2
MOUNTING THE HAND SHOWER
A. Remove the protector neck (23)
from the deck handshower holder tube
(27). Slide in the foam washer (24) up
the end of the tube or you may want to
use putty to seal this unit to the tub
deck.
B. Insert the deck handshower hold-
er through the hole of the deck and
secure with metal washer (20) and the
hexagonal nut (22). Tighten firmly.
C. Now slide the protector neck (23)
back onto the end of the tube (27)
D. Take your handshower (29) and
your deck elbow (30) and thread firmly
together with washer (26). Now
connect the chrome flexible hose with
conical end (21) to the hand shower
elbow (30) with washer (31). Tighten
firmly
E. Now slide the flexible hose with
handshower attached through the top
of the holder (27)
3 FLEXIBLE HOSES CONNECTION
A. Insert the rubber washers in the 1/2" female and 3/4" female
nuts at the ends of the flexible hose (35)
B. Connect the flexible hose (35) to the 1/2" adaptor (15) of the
mixer (19) and the 3/4" end to the T section of the spout (2).
Secure firmly without twisting the hoses
C. Take the extension hose (32) and mount the 3/8"male end of
the hose into the female end of the chrome deck hose (21) sealing
this with rubber washer (33). Tighten firmly. Finally mount the
female end of the extension hose (32) with rubber washer (34)
onto the male end of the check valve (36)
Ø1 3/8" MIN.
Ø1 1/2" MAX.
T
15
14
25
26
Products info: www.aquabrass.com
last revision: 05/21/2013
31
26
30
21
27
24
20
22
23
2
11
19
26
24
3/8"
robinet de bain 4 morceaux avec douchette
4
MOUNTING THE MIXER
A. Each faucet is supplied with a hot
and cold valve. Make sure you mount
hot (15) on the LH and cold (19) on the
RH when facing the faucet.
29
B. Take the hot valve (15) and mount
the tight fitting nut (18) halfway down
valve body with 2 little screws down.
Follow with the metal washer (17) adn
rubber washer (16). Push through the
under side and secure with flange
anchoring nut (22). You have set the
proper valve height when this anchor-
ing nut is completely threaded. Now
yuou can secure valve tightly with the
both added screw (20).
C. Doi the same on cold valve (19).
Make sure your valve outlets are
toward the spout.
5
AFTER WATER CONNECTION
A. We recommend to connect hot and cold water supply hoses (14)
from the mixer (19) to the 3/8" shut-off valves (not included)
B. When the connections are made, turn on the mixer. Check all
joints for leaks. Tighten as needed.
C. Flush out both lines again before you thread your aerator (1) back
into the spout.
D. Turn on the mixer and with the water now running from the spout
(2), pull up on the diverter to verify that the water is now diverted
properly to the hand shower. Now turn off the mixer and the spring
loaded diverter will return back to spout.
Only use the diverter to divert from the spout to the hand
shower. Do not divert back and forth with the water running.
Use only as instructed.
TAKING CARE OF YOUR AQUABRASS PRODUCT
To clean your AQUABRASS faucet or accessory, wash with a wet non-
abrasive soapy cloth. Then wipe dry with a soft towel or cloth .We
recommend this be done on a regular basis.
DO NOT USE ANY ABRASIVE , CHEMICAL OR CORROSIVE, POWDER
OR ANY OTHER STRONG CLEANERS INCLUDING DETERGENTS, WIN-
DOW CLEANERS AND DESINFECTANTS ON YOUR AQUABRASS PROD-
UCT as they will destroy the finish and therefore VOID THE WARRAN-
TY. Toothpaste remnants should also be rinsed off when necessary.
Ask your plumbing retailer about our PROTECTANT-CLEANER now
available from AQUABRASS. This product is specially manufactured to
clean and polish leaving a protective coating to maintain your products
shine and finish.
geo 27418
4-piece tub filler with handshower
ZG718- GG718
Deckmount 4pc tub set
22
16
17
19
18
20
15
Updated 07-27-10
aquabrass.com
Publicité
