Axis Communications M2035-LE Instructions D'installation page 3

Electromagnetic compatibility
(EMC)
This equipment has been designed and tested to
fulfill applicable standards for:
•
Radio frequency emission when installed
according to the instructions and used in
its intended environment.
•
Immunity to electrical and
electromagnetic phenomena when
installed according to the instructions
and used in its intended environment.
USA
This device complies with part 15 of the FCC
Rules. Operation is subject to the following two
conditions:
1. This device may not cause harmful
interference, and
2. this device must accept any interference
received, including interference that may
cause undesired operation.
This equipment has been tested using an
unshielded network cable (UTP) and found to
comply with the limits for a Class A digital
device, pursuant to part 15 of the FCC rules.
This equipment has also been tested using a
shielded network cable (STP) and found to
comply with the limits for a Class A digital
device, pursuant to part 15 of the FCC rules.
These limits are designed to provide reasonable
protection against harmful interference when
the equipment is operated in a commercial
environment. This equipment generates,
uses, and can radiate radio frequency energy
and, if not installed and used in accordance
with the instruction manual, may cause
harmful interference to radio communications.
Operation of this equipment in a residential
area is likely to cause harmful interference in
which case the user will be required to correct
the interference at his own expense.
Contact information
Axis Communications Inc.
300 Apollo Drive
Chelmsford, MA 01824
United States of America
Tel: +1 978 614 2000
Canada
This digital apparatus complies with
CAN ICES-3 (Class A). The product shall
be connected using a shielded network
cable (STP) that is properly grounded. Cet
appareil numérique est conforme à la norme
CAN NMB-3 (classe A). Le produit doit être
connecté à l'aide d'un câble réseau blindé (STP)
qui est correctement mis à la terre.
Europe
This digital equipment fulfills the requirements
for RF emission according to the Class A limit of
EN 55032. The product shall be connected using
a shielded network cable (STP) that is properly
grounded. Notice! This is a Class A product. In
a domestic environment this product may cause
RF interference, in which case the user may be
required to take adequate measures.
Australia/New Zealand
This digital equipment fulfills the requirements
for RF emission according to the Class A limit
of AS/NZS CISPR 32. The product shall be
connected using a shielded network cable (STP)
that is properly grounded. Notice! This is a
Class A product. In a domestic environment this
product may cause RF interference, in which
case the user may be required to take adequate
measures.
Japan
この装置は、クラスA機器です。この装
置を住宅環境で使用すると電波妨害を引
き起こすことがあります。この場合には
使用者が適切な対策を講ずるよう要求さ
れることがあります。 VCCI ‒ A
本製品は、シールドネットワークケーブ
ル(STP)を使用して接続してください。ま
た適切に接地してください。
本製品は電気通信事業者（移動通信会
社、固定通信会社、インターネットプロ
バイダ等）の通信回線（公衆無線 LAN を
含む）に直接接続することができませ
ん。本製品をインターネットに接続する
場合は、必ずルータ等を経由し接続して
ください。
Korea
이 기기는 업무용 환경에서 사용할 목
적으로 적합성평가를 받은 기기로서 가
정용 환경에서 사용하는 경우 전파간섭
의 우려가 있습니다. 적절히 접지된 STP
(shielded twisted pair) 케이블을 사용하
여 제품을 연결 하십시오.
Safety
This product complies with IEC/EN/UL 62368-1,
safety of audio/video and IT equipment, and
IEC/EN/UL 60950-22, Safety of Information
Technology Equipment.
When used with Power over Ethernet (PoE),
the Power Sourcing Equipment (PSE) shall
comply with IEEE 802.3af and Limited Power
Source (LPS) according to annex Q of IEC/EN/UL
62368-1.
We recommend the use of Axis midspans or Axis
PoE switches.
3