CANGAROO CHRISTIANO Notice D'utilisation page 11

• Do not overload the stroller! Any load placed and / or attached to the handle, board, backrest, canopy and /
or sides of the stroller can affect its stability! The stroller and the seat are designed to carry only one child!
• Do not use spare parts and other components not supplied by the manufacturer! The manufacturer accepts
no liability for safety if used spare parts, different from the original ones or approved by the approved type.
• Do not make changes or modifications to the construction! If necessary, contact your supplier or an
authorized service centre for advice and repair.
• The car seat does not replace the baby seat or crib. When the baby does not need sleep, it should be placed
in a suitable baby stroller, seat or crib.
• Do not use the product if you find any missing or damaged parts!
• Do not allow children under 3 years of age to fully assemble the product to avoid access to small and
disassembled parts!
• Do not place additional cords or ties on the product to avoid the risk of suffocation!
• Do not use the stroller on escalator and be careful when getting down or up on the sidewalk.
• Keep the plastic packaging away from children to avoid the risk of suffocation!
• DO NOT store the product in humid places and in direct sunlight!
SEE FIGURE PD: 1.One hand fold button; 2.Canopy; 3. Shoulder pads; 4. Safety bumper; 5. 5-point safety belt;
6.Seat cushion; 7.Footrest; 8.Front wheel detaching button; 9.Front wheels; 10. Rear wheels; 11. Footrest
adjustment button; 12. Safety bumper detaching button; 13. Seat detaching button; 14.Push handle; 15.Seat
adjusting button; 16.Push handle height adjustment button;17.Luggage basket; 18.Brake pedal; 19.Direction
lock. 20.Carrycot
1.ASSEMBLY OF THE STRUCTURE– FIGURES 1-4: Take the seat and frame of the stroller out of the carton
(Figure 1).
• UNFOLDING OF THE STROLLER FRAME – FIGURE 2: Grab the handle and pull upwards until stroller opens
and you hear a click sound.
• UNFOLDING THE SEAT – FIGURE 3: Unfold the seat as shown in Figure 3 and place it on a flat surface. Adjust
the seatback incline by pulling the button indicated in Figure 3.
•
INSTALLING THE SEAT ON THE FRAME OF THE STROLLER– FIGURE 4: To install the seat, put it in the frame
holes until you hear a click sound.
2.INSTALLING AND REMOVING THE FRONT WHEELS – FIGURES 5-6: Insert the front wheel into the front
frame opening as shown in Figure 5. Fix until you hear a click. To remove the front wheel, press the button for
removal and pull the wheel downwards (Figure 6).
3.ORIENTATION OF THE FRONT WHEELS – FIGURE 7: Press the lever downwards to activate the straight
direction of front wheels. Pull the lever upwards to activate the swiveling of front wheels.
4.INSTALLING AND REMOVING THE REAR WHEELS – FIGURES 8-9: Insert the rear wheel into the rear frame
opening and fix until you hear a click (Figure 8). To remove the rear wheels, push the button and the wheels
are released quickly by pulling (Figure 9).
5.USING THE REAR BRAKE – FIGURE 10: To activate the parking device and lock the two rear wheels, press
down the pedal on the rear axle. To release the brake, pull up the pedal using your foot.
6.ATTACH AND DETACH THE SAFETY BOARD – FIGURES 11-12: Insert both ends of the safety board into the
two side holes of the frame. Secure the guard until you hear a click (Figure 11). To remove the guard, press the
release button on both sides of the frame and pull at the same time (Figure 12).
7.SEAT ADJUSTMENT/SEAT RECLINATION – FIGURE 13: Pull the handle out, as shown in figure 13 and hold it,
at the same time move the seat upwardly or downward to change the seat angle you want.
8.CHANGING THE DIRECTION OF THE SEAT – FIGURES 14-15: To change the direction of the seat, press the
buttons on either side of the seat. Pull out the seat, then turn it over to the desired direction and put it back
into the designated slots, as shown in figures 14 and 15.
9.ADJUSTING THE POSITION OF THE HANDLE – FIGURE 16: As shown in Figure 16, the position of the handles
can be adjusted by pressing the two side buttons of the frame and moving the handle to the desired position.
10.OPERATION WITH THE CANOPY - FIGURES 17-19: Pull the canopy forwards, in order to unfold it and
backwards – in order to fold it.
PARTS
ASSEMBLY STEPS AND USE
10