Publicité
Les langues disponibles
Les langues disponibles
ELECTRICAL
EXTENSION CORDS
See Figure 1.
When using a power tool at a considerable distance from
a power source, be sure to use an extension cord that has
the capacity to handle the current the product will draw. An
undersized cord will cause a drop in line voltage, resulting
in overheating and loss of power. Use the chart to determine
the minimum wire size required in an extension cord. Only
round jacketed cords listed by Underwriter's Laboratories
(UL) should be used.
When working outdoors with a product, use an extension
cord that is designed for outside use. This type of cord is
designated with "WA" or "W" on the cord's jacket.
Before using any extension cord, inspect it for loose or
exposed wires and cut or worn insulation.
It is possible to tie the extension cord and power cord in a
knot to prevent them from becoming disconnected during
use. Make the knot as shown in figure 1, then connect the
plug end of the power cord into the receptacle end of the
extension cord. This method can also be used to tie two
extension cords together.
**Ampere rating (on product data plate)
0-2.0
2.1-3.4
Cord Length
25'
16
16
50'
16
16
100'
16
16
**Used on 12 gauge – 20 amp circuit.
NOTE: AWG = American Wire Gauge
WARNING
of the working area. Position the cord so that it will
not get caught on lumber, tools, or other obstructions
while you are working with a power tool. Failure to do
so can result in serious personal injury.
WARNING
each use. If damaged replace immediately. Never use
the product with a damaged cord since touching the
damaged area could cause electrical shock resulting
in serious injury.
ELECTRICAL CONNECTION
This product has a precision-built electric motor. It should
be connected to a power supply that is nominal 120V/60Hz
AC (typical U.S. household circuit). Do not operate this
product on direct current (DC). A substantial voltage drop
will cause a loss of power and the motor will overheat. If
the product does not operate when plugged into an outlet,
double-check the power supply.
SPEED AND WIRING
The speed is not constant and decreases under a load or
with lower voltage. For voltage, the wiring in a shop is as
important as the motor's horsepower rating. A line intended
3.5-5.0
5.1-7.0
7.1-12.0
Wire Size (A.W.G.)
16
16
14
16
14
14
14
12
10
Keep the extension cord clear
Check extension cords before
FIG. 1
A
A - Extension cord
B - Appliance cord
FIG. 2
A - Grounding pin
B - 120V Grounded outlet
12.1-16.0
only for lights cannot properly carry a power tool motor. Wire
14
that is heavy enough for a short distance will be too light for
12
a greater distance. A line that can support one power tool
–
may not be able to support two or three tools.
GROUNDING INSTRUCTIONS
See Figure 2.
This product must be grounded. In the event of a malfunction
or breakdown, grounding provides a path of least resistance
for electric current to reduce the risk of electric shock. This
product is equipped with an electric cord having an equip-
ment-grounding conductor and a grounding plug. The plug
must be plugged into a matching outlet that is properly
installed and grounded in accordance with all local codes
and ordinances.
Do not modify the plug provided. If it will not fit the outlet,
have the proper outlet installed by a qualified electrician.
WARNING
ed plug increase the risk of electric shock. When repair
or replacement of the cord or plug is required, take the
tool to an authorized service center.
Check with a qualified electrician or service personnel if the
grounding instructions are not completely understood, or if
in doubt as to whether the product is properly grounded.
Repair or replace a damaged or worn cord immediately.
This product is for use on a nominal 120 V circuit and has a
grounding plug similar to the plug illustrated in figure 2. Only
connect the product to an outlet having the same configu-
ration as the plug. Do not use an adapter with this product.
English
|
7
TIE CORDS AS SHOWN
B
A
A
Improper installation of a ground-
B
B
Publicité
