Publicité
Les langues disponibles
Les langues disponibles
English
2. Place drill bit in contact with the workpiece.
nOTE: Use sharp drill bit only.
3. Pull the trigger switch applying pressure in a straight line
with the bit until it reaches the desired depth.
WARNING: Tool may stall if overloaded causing a sudden
twist. Always expect the stall. Grip the tool firmly to control the
twisting action and avoid injury.
4. Keep the motor running when pulling the bit back out of
a drilled hole to prevent jamming.
Recommendations for Drilling
• When drilling, always apply pressure in a straight line with
the bit, but do not push hard enough to stall the motor or
deflect the bit.
• iF ThE TOOl sTAlls:
- RElEAsE TRiggER sWiTCh iMMEDiATElY, remove drill
bit from work, and determine cause of stalling.
- DO nOT DEPREss TRiggER sWiTCh On AnD OFF in
An ATTEMPT TO sTART A sTAllED TOOl—This CAn
DAMAgE ThE TOOl.
- To minimize stalling or breaking through the material,
reduce pressure on drill and ease the bit through the last
fractional part of the hole.
• Large holes (5/16" to 1/2" [7.9 mm to 12.7 mm]) in
steel can be made easier if a pilot hole (5/32" to 3/16"
[4 mm to 4.8 mm]) is drilled first.
• If drilling thin material or material that is prone to
splinter, use a wood "back-up" block to prevent damage to
the workpiece.
Hammerdrilling
DCD706 Only
Important: Use carbide-tipped or masonry bits rated for
percussion drilling only.
1. Select the desired speed/torque range using the
speed selector 6 to match the speed and torque to the
planned operation. Turn the mode selection collar 5 to the
hammerdrill symbol.
2. Pull the trigger, applying just enough pressure on the
hammer to keep it from bouncing excessively or "rising" off
the bit.
Recommendations for hammerdrilling
• Too much force will cause slower drilling speeds,
overheating, and a lower drilling rate.
• A smooth even flow of material indicates the proper
drilling rate.
• Drill straight, keeping the bit at a right angle to the
work. Do not exert side pressure on the bit when drillling
as this will cause clogging of the bit flutes and a slower
drilling speed.
• When drilling deep holes, if the hammer speed starts to
drop off, pull the bit partially out of the hole with tool still
running to help clear debris from the hole.
MAINTENANCE
WARNING: To reduce the risk of serious personal
injury, turn unit off and remove the battery pack
before making any adjustments or removing/installing
attachments or accessories. An accidental start-up can
cause injury.
8
Cleaning
WARNING: Blow dirt and dust out of all air vents with
clean, dry air at least once a week. To minimize the risk of eye
injury, always wear ANSI Z87.1 approved eye protection when
performing this procedure.
WARNING: Never use solvents or other harsh chemicals
for cleaning the non-metallic parts of the tool. These
chemicals may weaken the plastic materials used in these
parts. Use a cloth dampened only with water and mild soap.
Never let any liquid get inside the tool; never immerse any part
of the tool into a liquid.
Accessories
WARNING: Since accessories, other than those offered by
D
WALT, have not been tested with this product, use of such
e
accessories with this tool could be hazardous. To reduce the
risk of injury, only D
WALT recommended accessories should
e
be used with this product.
Recommended accessories for use with your tool are
available at extra cost from your local dealer or authorized
service center. If you need assistance in locating any
accessory, please contact D
(1-800-433-9258) or visit our website: www.dewalt.com.
MAXiMUM RECOMMEnDED CAPACiTiEs
Metal drilling
Wood, flat boring
Hole saws
Repairs
The charger and battery pack are not serviceable. There are
no serviceable parts inside the charger or battery pack.
WARNING: To assure product SAFETY and RELIABILITY,
repairs, maintenance and adjustment (including brush
inspection and replacement, when applicable) should
be performed by a D
WALT factory service center or a
e
D
WALT authorized service center. Always use identical
e
replacement parts.
Register Online
Thank you for your purchase. Register your product now for:
• WARRAnTY sERViCE: Registering your product will help
you obtain more efficient warranty service in case there is a
problem with your product.
• COnFiRMATiOn OF OWnERshiP: In case of an
insurance loss, such as fire, flood or theft, your registration of
ownership will serve as your proof of purchase.
• FOR YOUR sAFETY: Registering your product will allow
us to contact you in the unlikely event a safety notification is
required under the Federal Consumer Safety Act.
• Register online at www.dewalt.com.
WALT: call 1-800-4-D
WALT
e
e
Low Range (1)
High Range (2)
1/4" (6.35 mm)
1/8" (3.2 mm)
3/4" (19 mm)
1/2" (12.7 mm)
3/4" (19 mm)
5/8" (15.9 mm)
Publicité
