Télécharger Imprimer la page

CANGAROO DRACO Instructions Pour L'utilisation page 23

Publicité

Step 4: Press one of the ISOFIX connectors to engage it to the ISOFIX anchorage point with a 'click'. Repeat on the other side
to secure both ISOFIX connectors. The ISOFIX indicator should be green on both sides. Installation is completed. WARNING!
The ISOFIX connectors are only fitted correctly if both ISOFIX system indicators are marked green.
Step 5: Press the car seat firmly against the backrest of the vehicle seat. Shake the child seat to make sure it is securely
fastened and check the green safety buttons again.
Press the ISOFIX button again to release the lugs from the guides.
The upper anchor point is fixed device on the trunk or the floor of the vehicle. Pull the upper part of the top tether and press
the adjuster to secure the strap to the back of the car seat.
tether adjuster show „green color" If the indicator does not show green, reinstall.
ATTENTION! After installation make sure the car seat is firmly and securely secured.
To adjust the head support, pull and hold the head support release handle. Pull the handle up to move the head support to
a higher position. Hold the handle and push the head support down to move it to a lower position. When the head support
is in the desired position, release the handle to lock it.
If the child seat is used rear-facing, the head restraint should be adjusted so that the 5-point harness straps are at the
same height or slightly below the child's shoulders.
If the child seat is used forward-facing, the head restraint must be adjusted so that the straps of the 5-point harness
are at the same height or slightly above the child's shoulder.
To protect your child! The extra pad provides your child with the support they need while he or she is even smaller.The extra
padding is used to provide extra comfort for very small babies.
Attention! Please use the extra pad attached to this car seat model until your child reaches a height of 75 cm (approx. 3 months).
The newborn inlay may be removed after the baby is 75 cm to provide more space for the child. To remove the newborn inlay
open and remove the shoulder pads. Then remove the newborn inlay and place the shoulder pads back on the shoulder belts.
Step 1: Hold down the harness adjustment button and pull the shoulder belt towards you as far as possible. Make sure
to pull the shoulder belt under the chest pads as shown in Figure 1.
Step 2: Press the red button on the 5-point belt buckle to unbuckle it.
Step 3: Put the child to sit in the seat. Slide the shoulder belts over the child's shoulders and tuck the tongues of the
buckle into each other. Lock the tucked tongues into the buckle.
Step 4: Pull both shoulder belts to tighten the lap belt. Make sure the lap belt is positioned low down so that the child's
pelvis firmly gripped.
Step 5: Pull up on the 5-point belt adjuster until the belt secures the child properly. Pull the two chest pads to the
lowest position.
ATTENTION! The 5-point safety harness of car seat must be removed when child reaches height 100-150 cm.
Step 1: Unlock the belt from central buckle, remove the crotch pad and insert the buckle through the slot of fabric
cover.
Step 2: Press and hold the button for shoulder belts adjustment. Remove the cover at the back of backrest, pull the
metal joint and split the shoulder belt from it. Place the metal joint into the slots of car seat and tighten it to prevent
falling.
Step 3: Lift the cover of head support and pull the shoulder belts at front to remove them.
Press the roation button to rotate the child seat to 180° или 360°. The seat is rotatable in both directions. By fixing in
required position (car seat FORWARD facing or REARWARD facing) you will hear a click sound.
INSTALLING THE TOP TETHER - FIGURE D
- FIGURE B.3
- FIGURE B.1
HEAD SUPPORT ADJUSTMENT - FIGURE E
- FIGURE B.3
- FIGURE B.1
THE NEWBORN INLAY - FIGURE E.1
- FIGURE B.3
- FIGURE B.1
PUTTING A 5-POINT SAFETY HARNESS- FIGURE F
REMOVING THE 5-POINT SAFETY HARNESS- FIGURE G
- FIGURE B.1
SEAT ROTATION- FIGURE H
- FIGURE B.1
BACKREST RECLINING- FIGURE I
- FIGURE B.1
Tighten the belt of the top tether, until the indicator of top
23

Publicité

loading

Produits Connexes pour CANGAROO DRACO

Ce manuel est également adapté pour:

K81