Chapin 2553E Mode D'emploi

WARNING
WARNING: Improper use or failure to follow instructions can result in explosive failure causing serious
eye or other injury. For safe use of this product you must read and follow all instructions. Do not leave a
pressurized sprayer in the hot sun. Heat can cause pressure build-up resulting in possible explosion.
Do not store or leave solution in tank after use. Always wear goggles, gloves, long sleeve shirt, long pants
and full foot protection when spraying. Never use any tool to remove pump if there is pressure in sprayer.
Never stand with face or body over top of tank when pumping or loosening pump to prevent ejecting pump
assembly and/or solution from striking and injuring you. Never pressurize sprayer by any means other than
the original pump. Do not attempt to modify this sprayer. Replace parts only with manufacturer's original
parts. Never spray flammable, caustic, acidic, chlorine, bleach or other corrosive solutions or heat,
pressure, or gas producing chemicals. Always read and follow chemical manufacturer's instructions
before use with this sprayer as some chemicals may be hazardous when used with this sprayer.
Parts, Piezas, Pièces
6-6136 6-4631 6-6003
Hose Fan Nozzle Nozzle
Manguera Tobera Tobera
Tuyau Buse Buse
6-4626 6-3337
Shut-off Handle Strap,
Mango de cierre Correa,
Poignée du robinet Sangle
6-7770
Extension wand, Vara de extensión, Rallonge
6-1925
Repair Kit (not included)
Juego de reparación (no incluido)
Kit de réparation (non inclus)
Note: Your particular sprayer may not include all parts pictured above.
Nota: Es posible que este pulverizador en particular no incluya todas las partes que se ilustran arriba.
Remarque : Votre pulvérisateur particulier pourrait ne pas inclure toutes les pièces illustrées plus haut.
CONGRATULATIONS!
YOU HAVE JUST PURCHASED A QUALITY CHAPIN PRODUCT.
REGISTER YOUR SPRAYER ONLINE @ WWW.CHAPINMFG.COM
VISIT US ON THE INTERNET: WWW.CHAPINMFG.COM
BEFORE RETURNING THIS PRODUCT FOR ANY REASON, PLEASE CALL:
1-800-950-4458
When calling, please have the following information available: Sales receipt & model number. This number
connects you directly with the manufacturer of this product. Our Technical Support Team will be happy to help
you with any assembly, troubleshooting and replacement information you may need.
1. Hose to Tank
2553E
1B
1A
Make sure white outlet tube Insert tube into tank.
is attached to hose.
1E
Slip hose nut down to
tank, turn clockwise
and tighten as tight
as possible by hand.
2. Nozzle/Extension
Sk-1154-1
2A
2B
2C
TO RETRACT EXTENSION - Grasp the locking nut and turn it counter-clockwise until loose. Push the brass tube
down into the base tube to desired length (CAUTION: POINT THE NOZZLE IN A SAFE DIRECTION. IF THE EXTENSION
HAS FLUID IN IT THE FLUID WILL SPRAY OUT OF THE NOZZLE WHEN PUSHING THE BRASS TUBE DOWN, POSSIBLY
CAUSING IT TO SPRAY ON YOU. YOU CAN ELIMINATE THIS BY REMOVING THE EXTENSION FROM THE SHUT-OFF AND
ALLOWING THE FLUID TO DRAIN.) Re-tighten the locking nut by turning it clockwise to hold brass tube in position.
3. Filter
The filter helps prevent clogging while spraying. It is located on the
end of the outlet tube inside your sprayer tank.To clean filter, remove
the discharge assembly from the tank (Fig.1A). Make sure the filter is
positioned at the bottom of the tank as pictured (Fig. 3A).
4. Pre-Use Check
1) Do: Check tightness of hose nut to be sure hose is securely attached to the tank outlet.
2) Do: Inspect hose for deterioration, cracks, softness, or brittleness. If any of these conditions are found, replace
hose before using. Replace with original manufacturer's parts only.
3) Do: Remove pump (see Filling, Pressurizing and Spraying Instructions), inspect interior and exterior of tank for
signs of deterioration of body and bottom. Any sign of deterioration indicates possible tank weakening and could
result in explosive bursting under pressure. If any of these signs are found, discard tank immediately and replace.
Do not attempt to patch leaks, etc., as this could result in serious injury.
4) Do: Follow Filling, Pressurizing and Spraying Instructions, except use water only (Pump plunger 10-20 strokes and
inspect for leaks).
5) Do: Direct shut-off away from you and open to make sure discharge is not clogged.
6) Do: If unit passes this test, release pressure (see Pressure Releasing Instructions), empty tank, and proceed with
Filling, Pressurizing and Spraying Instructions.
7) Do: Inspect all metal parts including the wand, nozzle and fittings for rust, corrosion and pitting. If any of these
conditions are found, replace affected part with original manufacturer's part before using.
019235R0823
1C 1D
Proper placement of Line up tabs on safety lock
white outlet tube. connector with notches on
the outlet flange of the tank.
Insert tabs into notches to
form a secure seal.
Attach nozzle to shut-off handle or extension wand.
TO EXTEND EXTENSION - Grasp locking nut and turn counter-clockwise
until loose. Pull brass tube up to desired length and re-tighten locking
nut by turning clockwise until tight. DO NOT USE TOOLS AS THIS WILL
DAMAGE EXTENSION.
3A
Filter
5. Filling
1) Do: Turn pump handle counterclockwise and remove pump
2) Do: Prepare spray solution following all directions and safety warnings on chemical label.
3) Do: Fill tank to no more than the proper gallon marker. Do NOT: overfill to accommodate pump.
4) Do: Check pump to make sure that no grass or dirt is stuck to barrel. Replace pump in tank and tighten securely.
6. Pressurizing and Spraying
6A 6B 6C
Do: Turn handle clockwise Do: Pump until you feel Do: Push handle, down,
to tighten. Push handle resistance. turn 1/4 turn clockwise to
down, turn 1/4 turn lock. Begin spraying. Re-
counterclockwise to pump sprayer as required
release. to maintain spray force.
7. To Release Pressure
1) Do: With pump facing away, turn locked handle counterclockwise until air begins to escape.
Stop turning handle when you hear air escaping.
2) Do: Stay away from the sprayer until all air has escaped.
8. Care, Storage and Maintenance
1) Do: Follow chemical manufacture's instructions for cleaning. Rinse thoroughly with recommended solvent.
Follow Filling, Pressurizing and Spraying Instructions, except pump unit only 8-10 strokes. Be sure that the
wand and nozzle are thoroughly rinsed after each use.
2) Do: Open shut-off and allow water to run through discharge assembly.
3) Do: Release pressure (Follow Pressure Release Instructions), remove pump and empty sprayer.
4) Do: Store sprayer tank upside down, with pump removed, in a warm dry location.
5) Do: Periodically oil pump by dropping 10-12 drops of light oil down pump rod through opening in cover.
9. Fatigue-Free Spraying
For constant spraying, push down on shut-off handle and move grey locking
mechanism away from you. To release, squeeze handle and move the grey locking
mechanism back towards you. ( Not all models are provided with this feature).
10. Troubleshooting
-
Tank pressurizes but does not spray.
WARNING:
Release pressure in tank before troubleshooting.
Clean shut-off (Fig. 10A- 10D)
10A 10B 10C
Handle
Plunger
Diaphragm
Spring
Remove plunger, diaphragm and
Pull handle
Insert notches
spring. Wash diaphragm with
straight up. from underside of
mild detergent. Reassemble: Hold
handle into plunger
shut-off upright as shown, place
grooves and turn
spring in hole, place diaphragm on
counterclockwise.
top of spring. Reassemble plunger
and tighten.
Clean Nozzle Assembly (Fig. 10E)
10E
Nozzle Cap
Remove nozzle cap by unscrewing.
Clean and re-assemble.
P.O. Box 549 700 Ellicott St.
Batavia, NY 14021-0549 U.S.A.1-800-950-4458 www.chapinmfg.com
6D
Adjust spray pattern
by turning nozzle cap.
Do not turn cap more
than 2 turns or cap may
come off allowing spray
material to spray back
on you.
9A
Locking
mechanism
10D
Plunger flush
with body
Tighten plunger clockwise until
flush to top of shut-off body. Do
not over-tighten or unit may not
spray. Slide forks under plunger,
push handle down until it snaps
into place.