EINHELL GE-LC 18/25-1 Li Instructions D'origine page 23

3. Proper use
This cordless chainsaw is intended for felling
small trees, for sawing trunks, branches, wooden
beams and boards etc., and for performing cross
cuts and longitudinal cuts. and can be used for
cross cuts and longitudinal cuts. It is not suitable
for cutting any materials other than wood.
The equipment is to be used only for its prescri-
bed purpose. Any other use is deemed to be a
case of misuse. The user / operator and not the
manufacturer will be liable for any damage or inju-
ries of any kind caused as a result of this.
Please note that our equipment has not been de-
signed for use in commercial, trade or industrial
applications. Our warranty will be voided if the
machine is used in commercial, trade or industrial
businesses or for equivalent purposes.
4. Technical data
Motor power supply: ............................... 18 V DC
Idle speed n : ......................................2400 min
0
Battery charger output voltage: .............. 20 V DC
Battery charger output current: ....................... 3 A
Charging unit
supply voltage: .................... 200-250V~ 50-60Hz
Battery type: ............................................... Li-Ion
Number of battery cells: ................................... 5
Battery capacitance: .................................... 3 Ah
Cutter rail length ...................................... 250 mm
Max. cutting length: ................................ 230 mm
Cutting speed at rated rpm: ......................4.5 m/s
Oil tank capacity: .......................................200 ml
Weight ........................................... approx. 2.6 kg
Chain type ..............................Oregon 90PX040X
......................................... Kangxin 3/8.04340DL
Cutter rail type ...................Oregon 104MLEA041
....................................... Kangxin AP10-40437P
Danger!
Sound and vibration
Sound and vibration values were measured in ac-
cordance with EN 62841-1 and EN 62841-4-1.
L sound pressure level ..................... 88,2 dB(A)
pA
K uncertainty ............................................. 3 dB
pA
L sound power level ........................ 97,1 dB(A)
WA
Anl_GE_LC_18_25_1_Li_Kit_SPK13.indb 23 Anl_GE_LC_18_25_1_Li_Kit_SPK13.indb 23
GB
K uncertainty ........................................ 2,88 dB
WA
L sound power level guaranteed ....... 100 dB(A)
WA
Wear ear-muff s.
The impact of noise can cause damage to hea-
ring.
Total vibration values (vector sum of three direc-
tions) were determined in accordance with EN
62841-1 and EN 62841-4-1.
Handle under load
Vibration emission value front handle
a = 4,78 m/s
2
h
Vibration emission value rear handle
a = 4,67 m/s
2
h
K uncertainty = 1.5 m/s
The stated vibration emission levels and stated
noise emission values were measured in ac-
cordance with a set of standardized criteria and
can be used to compare one power tool with
another.
The stated vibration emission levels and stated
-1
noise emission values can also be used to make
an initial assessment of exposure.
Warning:
The vibration and noise emission levels may vary
from the level specifi ed during actual use, depen-
ding on the way in which the power tool is used,
especially the type of workpiece it is used for.
Keep the noise emissions and vibrations to a
minimum.
•
Only use appliances which are in perfect wor-
king order.
•
Service and clean the appliance regularly.
•
Adapt your working style to suit the appliance.
•
Do not overload the appliance.
•
Have the appliance serviced whenever ne-
cessary.
•
Switch the appliance off when it is not in use.
•
Wear protective gloves.
5. Before starting the equipment
Warning!
Always remove the battery pack before making
adjustments to the equipment.
- 23 -
2
07.12.2022 10:15:22 07.12.2022 10:15:22