Publicité
Page 8 of 12
Pour commencer, enfoncez 4 des bouchons en caoutchouc (article 3) fournis dans les trous
•
entourés en jaune sur le schéma de montage, dans le bon sens.
•
Retirez le boulon de montage inférieur du radiateur fléché sur la Photo 1.
Présentez la protection radiateur en position, en vous assurant que le bloc ABS et tous les câbles
•
soient dégagés de la protection du radiateur.
Fixez le support de protection radiateur au support de radiateur inférieur à l'aide du boulon
•
d'origine, ne serrez pas complètement à ce stade.
Fixez sans serrer le serre-câble de gauche autour de la boucle de retenue du câble, comme illustré
•
sur la Photo 2.
Fixez le serre-câble de droite autour du support de montage du bloc ABS comme indiqué sur la
•
photo 3.
Serrez complètement le serre-câble de gauche.
•
Si un accès plus large est nécessaire aux supports de serre-câbles, retirez le panneau de carénage
•
fléché sur la photo 4.
Serrez maintenant complètement le boulon de montage inférieur au couple spécifié.
•
Voir plus de produits R&G pour votre moto via ce lien :
R&G Racing | Cleaning/Lubrication - Gleam range for All Vehicles (rg-racing.com)
The catalogue description and any exhibition of samples are only broad indications of the Products and R&G may make design
changes which do not diminish their performance or visual appeal and supplying them in such state shall conform to the order.
The Buyer acknowledges no representation or warranty (other than as to title) has been given or will apply to the Products other
than those in R&G's order or confirmation and the Buyer confirms it has chosen the Products as being of merchantable quality
and suitable for its particular purposes. Where R&G fits the Products or undertakes other services it shall exercise reasonable
skill and care and rectify any fault free of charge unless the workmanship has been disturbed. The Buyer is responsible for
ensuring that the warranty on the motorcycle is not affected by the fitting of the Products. On return of any defective Products
R&G shall at its option either supply a replacement or refund the purchase money but shall not be liable if the Products have
been modified or used or maintained otherwise than in accordance with R&G's or manufacturer's instructions and good
engineering practice or if the defect arises from accident or neglect. Other than identified above and subject to R&G not limiting
its liability for causing death and personal injury, it shall not be liable for indirect or consequential loss and otherwise its liability
shall be limited to the amounts paid by the Buyer for the Products or the fitting or service concerned. These terms do not affect
the Buyer's statutory rights.
Returns must be pre-authorised (if not pre-authorised the return will be rejected). Goods may only be returned direct to us if
they were purchased direct from us (customer must prove if necessary). Otherwise to be returned to original vendor. Goods
must be in re-sellable condition, in the opinion of R&G Racing. All returns are subject to a 25% restocking and handling fee (25%
of the gross value exc. P&P – at the prevailing price at time of purchase). The customer must pay any and all carriage charges.
No returns of discontinued products, unless within 14 days of purchase. This policy does not affect your statutory rights and does
not refer to faulty goods.
Unit 1, Shelley's Lane, East Worldham, Alton, Hampshire, GU34 3AQ
Tel: +44 (0)1420 89007 Fax: +44 (0)1420 87301
NOTICE DE MONTAGE
ISSUE 1 – 18/04/2023 (MH)
CONSUMER NOTICE
R&G RACING RETURNS POLICY (NON-FAULTY GOODS)
R&G Racing
www.rg-racing.com
Email:
RAD0314PRO
info@rg-racing.com
Publicité
