Product Specifications - Kinetico Mach Série Guide D'utilisation

Product Specifications

Model 0s 00s*
Certified flow rate 8 gpm 9 gpm
@ 15 psi (or less) 30 .3 Lpm 34 . 1 Lpm
Peak flow rate**@ 12 gpm 16 .5 gpm
30 psi (or less) 45 .4 Lpm 62 .5 Lpm
Resin per tank, 0 .3 0 .47
in cubic feet
Resin per tank, in liters 8 .5 13 .3
Capacity per cycle, 4693 @ 1 .25 7867 @ 1 .8*
in grains @ salt used per 9802 @ 2 . 7
cycle setting pounds
Capacity per cycle, in 304 @ 0 .57 509 @0 .81*
grams @ salt used per 635 @ 1 .2
cycle setting kilograms
Grains exchanged 3754 @ 1 .25 4371 @ 1 .8*
per pound of salt used 3630 @ 2 . 7
Grains exchanged per 534 @ 0 .57 628 @ 0 .81*
kilograms of salt used 529 @ 1 .2
Max. flow rate to drain
2 .3 gpm 0 .69 gpm
during regenerations 8 . 7 Lpm 2 .6 Lpm
Min./max. operating 103 .4 - 861 .9 kPa
pressure
15 - 125 psi
Min./max. operating 2 - 49°C
temperature 35 - 120°F
Max. working 861 .9 kPa
pressure in psi 125 psi
* Meets California efficiency requirements of 4000 grains exchanged per pound of salt used. Efficiency is only
certified at the low salt dosage and was determined in accordance with NSF/ANSI 44.
** Manufacturer' s tested and verified rate- not certified or verified by NSF or WQA
*** Certification pending
Sodium Information: Systems using sodium chloride for regeneration will add sodium to the water. The
amount of sodium added is proportionate to the amount of hardness removed. People who are on sodium-
restricted diets should consider the added sodium as part of their overall sodium intake.
Inlet Hardness Sodium Added
171 mg/L (10 gr) 79 mg/L
342 mg/L (20 gr) 149 mg/L
513 mg/L (30 gr) 223 mg/L
1192 mg/L (40 gr) 298 mg/L
Kinetico reverse osmosis systems will remove as much as 98 percent of sodium content in the water. Using
potassium chloride as a regenerant will not add sodium to the water.
1
00s with 00s 00s
Overdrive
00c
00c with (Europe only)
Overdrive
11 gpm 7 gpm 11 .6 gpm
41 .6 Lpm 26 .5 Lpm 43 .9 Lpm
15 gpm 15 gpm 30 gpm
56 . 7 Lpm 56 . 7 Lpm 113 .5 Lpm
0 .4 0 .4 0 . 7
11 .3 11 .3 19 .8
5222 @ 1 . 0 * 5222 @ 1 . 0 * 12,481 @ 2 . 7 *
15,817 @ 4 . 0
338 @ 0 .45* 338 @ 0 .45* 809 @ 1 .23*
1025 @ 1 .8
5222 @ 1 . 0 * 5222 @ 1 . 0 * 4623 @ 2 . 7 *
3954 @ 4 . 0
751 @ 0 .450* 751 @ 0 .450* 658 @ 1 .23*
569 @ 1 .8
1 .5 gpm 1 .5 gpm 2 .5 gpm
5 . 7 Lpm 5 . 7 Lpm 9 .5 Lpm
00s with 100s 100s with
Overdrive Overdrive
20 .5 gpm 12 gpm 21 gpm
77 .6 Lpm 45 .4 Lpm 79 .5 Lpm
30 gpm 19 gpm 31 gpm
113 .5 Lpm 71 .9 Lpm 117 .3 Lpm
0 . 7 1 .5 1 .5
19 .8 42 .5 42 .5
12,481 @ 2 . 7 * 25,253 @ 5 .5* 25,253 @ 5 .5*
15,817 @ 4 . 0 41,087 @ 10 . 0 * 41,087 @ 10 . 0 *
809 @ 1 .23* 1636 @ 2 .5* 1636 @ 2 .5*
1025 @ 1 .8 2662 @ 4 .5* 2662 @ 4 .5*
4623 @ 2 . 7 * 4591* @ 5 .5* 4591* @ 5 .5*
3954 @ 4 . 0 4109* @ 10 . 0 * 4109* @ 10 . 0 *
658 @ 1 .29* 654 @ 2 .5* 654 @ 2 .5*
569 @ 1 .8 592 @ 4 .5* 592 @ 4 .5*
2 .5 gpm 3 .3 gpm 3 .3 gpm
9 .5 Lpm 12 .5 Lpm 12 .5 Lpm
1s 00s with 00s
Overdrive
(Europe Only***)
16 .4 gpm 11 gpm 6 gpm
62 . 1 Lpm 41 .6 Lpm 22 . 7 Lpm
22 gpm 15 gpm 15 gpm
83 .2 Lpm 56 . 7 Lpm 56 . 7 Lpm
2 .25 Upper: 0 . 4 Resin Upper: 0 . 4 Resin
Lower: 0 . 4 Carb Lower: 0 .4 Carb
63 . 7 Upper: 11 . 3 Resin Upper: 11 . 3 Resin
Lower: 11 . 3 Carb Lower: 11 .3 Carb
65,139 @ 15* 4921 @ 1 . 0 * 4921 @ 1 . 0 *
81,845 @ 30
4221 @ 6 .8* 319 @ 0 .45* 319 @ 0 .45*
5303 @ 13 .6
4343* @ 15 . 0 * 4921 @ 1 . 0 * 4921 @ 1 . 0 *
2728 @ 30 . 0
621 @ 6 .8* 709 @ 0 .45* 709 @ 0 .45*
390 @ 13 .6
4 .8 gpm 3 . 0 gpm 3 . 0 gpm
18 .2 Lpm 11 .4 Lpm 11 .4 Lpm
172 .3 - 861 .9 kPa 103 .4 - 861 .9 kPa
25 - 125 psi 15 - 125 psi
Kinetico Water Softeners (MACH 2025s, 2030s, 2040s OD, 2040c OD, 2050s, 2050c, 2060s,
2060s OD, 2100s, 2100s OD, 2175s, 4040s OD and 4060s OD with Macrolite or carbon)
are tested and certified by NSF International and/or the WQA against the requirements
of NSF/ANSI Standard 44 for softener performance and chemical reduction of barium and
radium 226/228. The Kinetico 4060s OD with Macrolite is tested and certified by NSF Inter-
national and/or the WQA against the requirements of NSF/ANSI Standard 42 for Particulate
Reduction Class III. The 4060s OD with carbon is tested against NSF/ANSI Standard 42 for
chlorine reduction. NSF International and/or the WQA certifies our product performance and
reviews our manufacturing facility and procedures to assure product consistency and integrity.
They also assure that our literature accurately reflects our product capabilities.
Certified Continuous Flow Rate as validated by NSF International represents continuous service
flow of water at 15 psi pressure drop and is not an indication of maximum flow rate or unit
limitation. U.S. Patents: 4,336,134; 4,579,242; 4,889,623; 4,972,877; 5,022,994; 5,490,932
These products are not intended to be used for treating water that is microbiologically unsafe or
of unknown quality without adequate disinfection before or after the system.
00s with 00s with
Overdrive- Overdrive-
Activated Macrolite
Carbon
11 gpm 10 gpm
41 .6 Lpm 37 .9 Lpm
15 gpm 15 gpm
56 . 7 Lpm 56 . 7 Lpm
Upper: 0 . 2 5 Carb Upper: 0 . 2 Macrolite
Lower: 0 . 7 Resin Lower: 0 . 7 Resin
Upper: 7 . 1 Carb Upper: 5 . 7 Macrolite
Lower: 19 . 8 Resin Lower: 19 .8 Resin
13,715 @ 4 . 0 14,883 @ 4 .4
889 @ 1 .8 964 @ 2 . 0
3429 @ 4 . 0 3383 @ 4 .4
494 @ 1 .8 482 @ 2 . 0
3 . 0 gpm 3 . 0 gpm
11 .4 Lpm 11 .4 Lpm
1