GE JCSP38DN4WW Instructions D'installation

Installation Instructions
30" Electric Slide-In Ranges
Questions?
Call 1.800.561.3344or visitwww.GEAppliances.ca
BEFORE YOU BEGIN
Read these instructions completely and carefully.
•
IMPORTANT--save
these instructionsfor local inspector's use.
•
IMPORTANT---Observe
all governing codes and ordinances.
• Note to Installer - Be sure to leave these instructionswith Consumer,
• Note to Consumer - Keep these instructions for future reference.
° Skill level - Installation of this appliance requires basic mechanical
skills and advanced electrical skills,
• Proper installation is the responsibilityof the installer.
• Productfailure dueto improperinstallation is not covered underwarranty.
AWARNING: This app,,ance must be properly
connected by means of the suppliedcord and plug. If your kitchen does not
have a receptacle, you must have one installed by a licensed electrician.
FOR YOUR SAFETY:
_ Anti-Tip
Bracket Kit
Included
If youdid not receivean anfl-tip
bracket withyour purchase,
call 1,800.561.3344 to receive
one at no cost.For installation
instructions o f the bracket,
visitwww.GEAppliances.ce.
A WARNIN
G---Before
beginning the installation,switch
power off at service panel and lock the service disconnectingmeans to
prevent power from being switchedon accidentally. When the service
disconnectingmeans cannot be locked, securelyfasten a prominent
warning device, such as a tag, to the service panel.
• All ranges can tip.
• BURNS or other SERIOUS
INJURIES can result.
• INSTALL and CHECK the
ANTI-TIP bracket following
the instructions supplied
with the bracket.
TOOLS YOU WILL NEED
Drill with 1/8" Bit Level
Safety Glasses Tape Measure
Adjustable Wrench
Pliers
1/4" Nut Driver
Ill REMOVE PACKAGING MATERIALS
Failure to remove packaging materials couldresult in damage to the
appliance. Remove all packingparts from oven, racks, heating elements
and drawer. Also, remove protectivefilmand labels on the door, cooktop
(do not remove side protection on glass cooktops) and backguard.
Do not remove protectivechannelfrom sides of glass cooktop, if applicable,
until later in installation.
NOTE: Cut the orangeshippingties from the powercord, being careful not
to damage the cord.
ALTERNATE INSTALLATION/
CONSTRUCTION KITS
Description:
Backguard_ Adds a decor-aWe b ackguard t otherearoftherange.Thiskitcan only
be usedwhentheopeninginthecountertop is63.5 cm (25")deep,
MaintopRllerlot: Adds a fillershiptothe rearof the range. T his kit can only be used
when the openinginthe countertop i s 63.5cm (25")deep.This kitcannot be used
witha backguard t _.
BodySide W.,'t: Coffins a color-matd"_l sidepanel w hichcan be usedtocreate
: a finished appearance o neithersideof the range.
LowerTrim Kit:Contains a coler-m_ toekick a.ndextra-long l eveling legs.
Designedto be usedwhen therangeneedsto be raisedhigherthan92.7crn (36-1/2").
To order accessory kits, call 1.800.661.1616, or visit www.GEAppliances.ca.
] 11-08 JR
31-10674
J
w
I" •
I-_ PREPARE THE OPENING
(FOR
INDOOR USE
ONLY)
If the countertoparea is not flat,excess tension may be applied to the glass
cooktopcausing breakage and voidingthe warranty. Make surethe wall
covedng,countertop,floodng and cabinetsaroundthe range can withstand
the heat (up to 93°C [200°F]) generated by the range.
A. Allow 76.2 cm (30") minimum clearance between surface unitsand bottom
of unprotected wood or metal cabinet, or allow a 61 cm (24") minimum
when bottomofwood or metal cabinet is protectedby no lessthen 6.3 mm
(1/4") thick flame retardantmillboardcovered with no less than No. 28 MSG
sheet metal .38 mm (.015")thick, .38 mm (.015") thick stainlesssteel,
.63 mm (.025")aluminum or .5 mm (.020") copper.
B. A minimum 15.2 cm (6") spacingto surfaces lessthan 38.2 cm (15")
above the ccoktop and adjacentcabinetry is recommended to reduce
exposure to steam, grease splatter and heat. Allow 6.3 mm (1/4")
minimum clearance at the back wall.
To reduce the dsk of bums or fire when reaching over hot surfaceelements,
cabinet storage space above the cooktop shouldbe avoided. If cabinet
storage space is to be providedabove the cooktop,the dsk can be reduced
by installinga range hood that projectsat least 12.7 cm (5") beyond the front
of the cabinets. Cabinets installedabove the cooktop must be no deeper
than 33 cm (13").
Front surface -_ 59.7 cm--61 cm 80 cm (31-1/2") - Metal cooktops
ofcountertop
, __
I _ _ 1 / to cool(top
I "]_,e_,.= _'"_ 91.1 cm-92.7 orn
,I_,,L _ _ I j- (35-7/8"-36-1/2")
.. -T-,,_-___.Z,,-_p.j_-__ oR
, I__.,.;"11 _ 27_986o
, I
, "_.__'_._---_1_t _'_ M / (36-1/2"-38")
'
I
// _.'_"_'l _ / Ihlowertnm
,,' .l ," I. 1 ]IL/
(_step2)
,.. -
49.5,_=-_2.3_.><_ I ;_">.-_1
79.4 cm (31-1/4") - Glass cooktops
/
7.3 cm (2-7/8") --_
' 91.1 cm-92.7 orn
711//
"
92.7 cm-96.5 Cmwith lower trim kit
49.5 cm-52.3 orn _
Door clearance
from front surface
. of countertop
I" 79.1 cm(31-1/8") ,1
CON to prevent inten_.mnce _h
the Storage drawer. Power cords
137 cm (4-1/2') to 182.2 orn (6')
longmay have to be dressed
to allow for proper drawer dosing. If the conb'ol panel measures 79.1 cm (31-1/8") as shown
above AND if the countertop has a raised edge, shave raised
edge to clear the control panel as shown below.
76.2 c[n /
_e°otel l -(_°")_°--t *
08. = (2s-)
3.1 =
(29-15/16"_o-1/1_')'-._1
]_
O_ e_ed_cal recoptade so the leng_ is parallel to the flonr,
l
• !
1.4_(_16_
f
6.3mm(1/4")T I
min. flat
/ I
63.5 cm (25")
(_zg_____ 1.4=1
(9/16") I
Smooth cut ._
76 crn-76.4 cm (29-15/16"-30-1/16"
Rat area
6,3 mm
91.4 crn (36")