Makita ADCF201 Manuel Du Propriétaire page 5

WARNING
• Do not allow familiarity with tools to make you careless. Remember that a careless fraction of a second is sufficient
to inflict serious injury.
WARNING
• Do not use any attachments or accessories not recommended by the manufacturer of this tool. The use of
attachments or accessories not recommended can result in serious personal injury.
This fan is equipped with a 2-speed control using the speed switch; you can also set run time for 1 hour, 2
hours, or 4 hours. Power supply can be with AC adaptor or battery cartridge (OPTIONAL ACCESSORIES).
USING AC ADAPTOR
Insert the 15V DC plug (Fig. 4) of AC adaptor into the 15V DC socket (Fig. 3), and then plug the AC pins (Fig. 4)
into a main power supply. Make sure that the voltage rating of the main power supply corresponds with that of the
adaptor.
To operate the cordless fan, first you need push the power switch button (1 in Fig. 1) to turn on the fan, now the fan
starts to work on high speed mode. If you want to change to low speed mode, push the speed change button (3 in
Fig. 1-1) and the speed indicator will show on low speed mode.
Push the power switch button (1 in Fig. 1) to turn off the unit after you finish using, then unplugged the AC adaptor
from the main power supply, and allow the cordless fan to cool completely before performing any inspection,
maintenance, cleaning procedures or storage.
SAVE THESE INSTRUCTIONS
It may delay 3 – 5s to start after the adaptor being inserted.
The adaptor might creak while using it for the power supply. This doesn't affect normal use.
IMPORTANT SAFETY INSTRUCTIONS
FOR BATTERY CARTRIDGE
1. Before using battery cartridge, read all instructions and cautionary markings on (1) battery charger, (2) battery,
and (3) product using battery.
2. Do not disassemble battery cartridge.
3. Recharge only with the charger specified by the manufacturer. A charger that is suitable for one type of battery
cartridge may create a risk of fire when used with another battery cartridge.
4. If operating time has become excessively shorter, stop operating immediately. It may result in a risk of
overheating, possible burns or even an explosion.
5. If electrolyte gets into your eyes, rinse them out with clear water and seek medical attention right away. It may
result in loss of your eyesight.
6. Do not shorten the battery cartridge:
(1) Do not touch the terminals with any conductive material.
(2) Avoid storing battery cartridge in a container with other metal objects such as nails, coins, etc.
(3) Do not expose battery cartridge to water or rain.
A battery short can cause a large current flow, overheating, possible burns and even a breakdown.
7. Do not store the tool and battery cartridge in locations where the temperature may reach or exceed 50°C (122°F).
8. Do not incinerate the battery cartridge even if it is severely damaged or is completely worn out. The battery
cartridge can explode in a fire.
9. Be careful not to drop or strike battery.
10. Do not use a damaged battery.
11. Follow your local regulations relating to disposal of battery.
SAVE THESE INSTRUCTIONS
CAUTION: Only use genuine Makita batteries.
Use of non-genuine Makita batteries, or batteries that have been altered, may result in the battery bursting causing
fires, personal injury and damage. It will also void the Makita warranty for the Makita tool and charger.
Tips for maintaining maximum battery life:
1. Charge the battery cartridge before completely discharged. Always stop tool operation and charge the battery
cartridge when you notice less tool power.
2. Never recharge a fully charged battery cartridge.
Overcharging shortens the battery service life.
3. Charge the battery cartridge with room temperature at 10°C – 40°C (50°F – 104°F). Let a hot battery cartridge
cool down before charging it.
4. Charge the battery cartridge if you do not use it for a long period (more than six months).
HOW TO OPERATE THE UNIT
5