12 Station power socket
13
Lift button for cartridge exchange
14 Station-to-shaver contacts
15 Clean&Charge Station display
15a Level indicator
15b Status light
15c Cleaning program indicators
16 Start button
17
Cleaning cartridge
Installing the Clean&Charge Station (see fig. D)
• Press the lift button (13) at the rear side of the
Clean&Charge Station to lift up the housing.
• Hold the cleaning cartridge (17) down on a flat,
stable surface (e.g. table).
• Carefully remove the lid from the cartridge.
• Slide the cartridge from the rear side into the base
of the station until it snaps into place.
• Slowly close the housing by pushing it down until it
locks.
• Connect the station to an electrical outlet by
snapping the special cord set (10) into the power
socket (12).
Charging the shaver in the Clean&Charge
Station (see fig. D)
Insert the shaver head with the front showing and
released head lock into the cleaning station.
Important: The shaver needs to be dry and free
from any foam or soap residue!
The contacts (7) on the back of the shaver need
to align with the contacts (14) in the station. Push
the shaver in the correct position. A beep sound
confirms that the shaver sits properly in the station.
Charging will start automatically.
Cleaning the shaver (see fig. D)
When the cleaning indicator
display, insert the shaver into the Clean&Charge
Station, as described above and press the start
button (16).
The hygiene status will be analyzed and is shown
by the cleaning program indicators (15c) in the
Clean&Charge Station display.
If status light (15b) does not shine (Clean&Charge
Station switches to stand-by after about
10 minutes), press start button twice. Otherwise
cleaning will not start. For best shaving results,
we recommend cleaning after each shave.
The cleaning process consists of several cycles, in
which cleaning fluid is flushed through the shaver
head. Depending on the program selected, the
cleaning time takes up to 3 minutes, followed by an
active drying phase of about 40 minutes, during
which a fan is running.
14
lights up in the shaver
Afterwards charging will resume, which is indicated
in the shaver display. When the shaver is fully charged
the display turns off.
Cleaning programs
short economical cleaning
normal level of cleaning
high intensive cleaning
Removing the shaver from the Clean&Charge
Station (see fig. E)
Hold the Clean&Charge Station with one hand and
tilt the shaver slightly to the front to release it.
Cleaning Cartridge / Replacement (see fig. F)
When the level indicator
nently red, the remaining fluid in the cartridge is
sufficient for about 3 more cycles. When the level
indicator blinks red, the cartridge needs to be
replaced (about every 3 weeks when used daily).
After having pressed the lift button (13) to open the
housing, wait for a few seconds before removing
the used cartridge to avoid any dripping. Before
discarding the used cartridge, make sure to close
the openings using the lid of the new cartridge,
since the used cartridge will contain contaminated
cleaning solution.
The hygienic cleaning cartridge contains ethanol or
isopropanol (specification see cartridge), which
once opened will naturally evaporate slowly. Each
cartridge, if not used daily, should be replaced after
approximately 8 weeks. The cleaning cartridge also
contains lubricants for the shaving system, which
may leave residual marks on the outer foil frame and
the cleaning chamber of the Clean&Charge Station.
These marks can be removed easily by wiping gently
with a damp cloth.
Accessories
Braun recommends changing your shaver's Foil &
Cutter cassette every 18 months to maintain your
shaver's maximum performance.
Available at your dealer or Braun Service Centres:
• Foil & Cutter cassette: 92S/92B
• Cleaning cartridge Clean&Charge Station: CCR
• Braun Shaver cleaner spray
Environmental notice
Product contains batteries and/or recyclable
electric waste. For environment protection do
not dispose of in household waste, but for
recycling take to electric waste collection
points provided in your country.
(15a) lights up perma-