Publicité
NOTICE DE MONTAGE
•
Pour monter la grille de protection sur la moto, couper la mousse autocollante fournie en bandeaux de 10mm puis collez les
au bas du cadre de protection radiateur, de façon à ce qu'ils se placent entre la grille de protection radiateur et le radiateur.
•
Prendre chaque grille de protection radiateur et appliquez un sticker en caoutchouc, voir la photo.
•
Enlever le boulon qui fixe le contour radiateur en plastique en place au bas du carénage, voir photo 2.
•
Tirer le contour radiateur en plastique du bas du radiateur (il peut être enlevé pour faciliter la tâche mais ce n'est
pas obligatoire) et glisser la grille de protection R&G situé derrière, voir photo 3.
•
Positionner la grille de protection radiateur pour cacher le radiateur, en veillant à ce que les 2 onglets sur le haut
soient places sous le contour radiateur en plastique sur le haut.
•
Repositionner le contour radiateur en plastique en placer de façon parallèle au radiateur. L'onglet plastique du
côté gauche doit se placer dans la fente du côté de la grille de protection radiateur, voir photo 4.
•
Le trou de fixation inférieur du contour radiateur en plastique doit s'aligner avec le support radiateur, prenant en
sandwich le trou de fixation de la grille de protection radiateur, voir photo 5. Remonter le boulon d'origine puis
serrer selon les valeurs de serrage recommandées.
•
Répéter cette opération des 2 côtés de la moto.
•
Vérifier que les protections soient correctement positionnées et que les panneaux en plastique soient fixés avant
de prendre la route.
The catalogue description and any exhibition of samples are only broad indications of the Products and R&G may make design changes which do not diminish their
performance or visual appeal and supplying them in such state shall conform to the order. The Buyer acknowledges no representation or warranty (other than as to title) has
been given or will apply to the Products other than those in R&G's order or confirmation and the Buyer confirms it has chosen the Products as being of merchantable quality
and suitable for its particular purposes. Where R&G fits the Products or undertakes other services it shall exercise reasonable skill and care and rectify any fault free of charge
unless the workmanship has been disturbed. The Buyer is responsible for ensuring that the warranty on the motorcycle is not affected by the fitting of the Products. On return
of any defective Products R&G shall at its option either supply a replacement or refund the purchase money but shall not be liable if the Products have been modified or used
or maintained otherwise than in accordance with R&G's or manufacturer's instructions and good engineering practice or if the defect arises from accident or neglect.
Other than identified above and subject to R&G not limiting its liability for causing death and personal injury, it shall not be liable for indirect or consequential loss and
otherwise its liability shall be limited to the amounts paid by the Buyer for the Products or the fitting or service concerned. These terms do not affect the Buyer's statutory
rights.
Returns must be pre-authorised (if not pre-authorised the return will be rejected). Goods may only be returned direct to us if they were purchased direct from us (customer
must prove if necessary). Otherwise to be returned to original vendor. Goods must be in re-sellable condition, in the opinion of R&G Racing. All returns are subject to a 25%
restocking and handling fee (25% of the gross value exc. P&P – at the prevailing price at time of purchase). The customer must pay any and all carriage charges. No returns of
discontinued products, unless within 14 days of purchase. This policy does not affect your statutory rights and does not refer to faulty goods.
Tel: +44 (0)1420 89007 Fax: +44 (0)1420 87301
R&G RACING RETURNS POLICY (NON-FAULTY GOODS)
Unit 1, Shelley's Lane, East Worldham, Alton, Hampshire, GU34 3AQ
ISSUE 1 19/11/18 (DM)
CONSUMER NOTICE
R&G Racing
www.rg-racing.com
Email:
info@rg-racing.com
Publicité
