Télécharger Imprimer la page

R&G RAD0095 Instructions De Montage page 2

Publicité

Pour installer la grille radiateur sur la moto, couper la mousse en bandeaux de 10mm et
collez-les au bas de la protection radiateur pour que les bandeaux soient entre la
protection et le radiateur.
Enlever la grille triangulaire
Enlever le panneau de remplissage devant le radiateur.
Enlever le carénage des 2 cotés.
Enlever les 2 boulons de fixation du bas (Photos 1 et 2).
Mettre la grille de protection radiateur en position à l'aide des boulons d'origine et fixer
(photos 1 et 2).
A l'aide des 2 attaches câble du kit, fixer la grille de protection à travers les fentes et
autour du haut du support de montage de radiateur (Couper le surplus d'attache qui
dépasse).
Remettre et fixer le carénage coté droit.
Glissez le support de pare fond de montage du radiateur sous l'écrou à ressort (photo 3).
Remettre et fixer le coté gauche du carénage (S'assurer que lorsque le boulon de fixation
du bas de carénage est fixé, le support de protection radiateur soit correctement mis en
place, pris en sandwich.
Remettre et sécuriser le panneau de remplissage devant le radiateur.
Remettre et fixer la grille triangulaire.
The catalogue description and any exhibition of samples are only broad indications of the Products and R&G may make design changes which do not
diminish their performance or visual appeal and supplying them in such state shall conform to the order. The Buyer acknowledges no representation or
warranty (other than as to title) has been given or will apply to the Products other than those in R&G's order or confirmation and the Buyer confirms it
has chosen the Products as being of merchantable quality and suitable for its particular purposes. Where R&G fits the Products or undertakes other
services it shall exercise reasonable skill and care and rectify any fault free of charge unless the workmanship has been disturbed. The Buyer is
responsible for ensuring that the warranty on the motorcycle is not affected by the fitting of the Products. On return of any defective Products R&G shall
at its option either supply a replacement or refund the purchase money but shall not be liable if the Products have been modified or used or maintained
otherwise than in accordance with R&G's or manufacturer's instructions and good engineering practice or if the defect arises from accident or neglect.
Other than identified above and subject to R&G not limiting its liability for causing death and personal injury, it shall not be liable for indirect or
consequential loss and otherwise its liability shall be limited to the amounts paid by the Buyer for the Products or the fitting or service concerned. These
terms do not affect the Buyer's statutory rights.
Returns must be pre-authorised (if not pre-authorised the return will be rejected). Goods may only be returned direct to us if they were purchased direct
from us (customer must prove if necessary). Otherwise to be returned to original vendor. Goods must be in re-sellable condition, in the opinion of R&G
Racing. All returns are subject to a 25% restocking and handling fee (25% of the gross value exc. P&P – at the prevailing price at time of purchase). The
customer must pay any and all carriage charges. No returns of discontinued products, unless within 14 days of purchase. This policy does not affect your
statutory rights and does not refer to faulty goods.
Unit 1, Shelley's Lane, East Worldham, Alton, Hampshire, GU34 3AQ
Tel: +44 (0)1420 89007 Fax: +44 (0)1420 87301
Le kit doit contenir
1x Protection radiateur (RAD0095)
3x 100mm Longueurs de mousses.
2 x Cable / Attaches câble.
CONSUMER NOTICE
R&G RACING RETURNS POLICY (NON-FAULTY GOODS)
R&G Racing
www.rg-racing.com
Email:
info@rg-racing.com

Publicité

loading