BorMann PRO BTC5500 Mode D'emploi page 2

EN
SYMBOLS
Wear eye protection.
SAFETY INSTRUCTIONS
Warning: Read the manual carefully before use. Failure to follow the warnings and instructions may result in tool damage, physical injury
and/or damage to property. Store the manual in a safe place for future reference.
• Read and understand this instruction manual before operating.
• Stay alert. Do not operate while under the influence of drugs, alcohol, or medication.
• Always wear safety approved eye protection with side shields.
• Keep work area clean and free of debris.
• Keep children and unauthorized persons away from the laminate cutter and the work area.
• Make sure tool is secure. Operate only on a firm substrate or solid stand.
• Use the right tool. Do not push the cutter and do not use it for work for which it is not intended. This tool is designed to cut: residential grade/low-pressure
laminate flooring, engineered wood flooring, vinyl composite tile, PVC tile, fiber cement board siding, vinyl siding, and pressboard lap siding. (*see Cut Guide).
• Keep the blade sharp. A dull blade will not perform properly.
• Always keep hands away from the blade while operating or carrying the tool.
• Do not alter or misuse this tool. It is manufactured with precision; modifications not specified in this manual may result in dangerous conditions.
• Maintain with care. Follow the instructions for cleaning, lubricating and changing accessories.
• Use only recommended accessories. The use of improper accessories may cause hazards or injury.
• Never leave the cutter unattended. Secure the handle with the safety lock when not in use (*see Cuts).
• Warning: the dust generated by cutting certain wood, wood fiber and/or PVC products can be injurious to your health. The laminate cutter generally does
not produce any dust; however, minimal dust may be generated. Avoid ingesting dust generated during cutting.
TECHNICAL SPECIFICATIONS
Technical data
Model BTC5500
Cut Width 330 mm
Cut Thickness 15 mm
Material Steel and aluminium
Angle Cut 45°-90°
Cut Seamless
Operation Quick, No Noise, No Dust
No sharp edge, long handle for more power,
Other features
compact design
ASSEMBLY INSTRUCTIONS
(3) Socket hex head
screws (Pre-installed)
Fastening
Assembly
(2) 6mm x 50mm
Phillips head screws
(4) 5mm x 30mm
Phillips head screws
2
Keep hands away from the blade.
Handle
(2) 4mm x 30mm
Self tapping screws
(2) 6mm x 35mm
Phillips head screws
Rail
Tail
Table
WWW.NIKOLAOUTOOLS.COM
* The manufacturer reserves the right to make minor changes to product design and technical
specifications without prior notice unless these changes significantly affect the performance and
safety of the products. The parts described / illustrated in the pages of the manual that you hold in
your hands may also concern other models of the manufacturer's product line with similar features
and may not be included in the product you just acquired.
* To ensure the safety and reliability of the product and the warranty validity, all repair, inspection
or replacement work, including maintenance and special adjustments, must only be carried out by
technicians of the authorized service department of the manufacturer.
* Always use the product with the supplied equipment. Operation of the product with non-provided
equipment may cause malfunctions or even serious injury or death. The manufacturer and the
importer shall not be liable for injuries and damages resulting from the use of non-conforming
equipment.
Note! #2 Phillips head screwdrivers will be required.
Hex key and hex screws are enclosed.
1. Fasten the table to the fastening assembly using Phillips B (4) 5x30
mm screws.
2. Fasten the rail to the power head assembly with A (2) Phillips 6x50
mm screws.
3. To install the handle, first remove the hex head screws (pre-
installed on the top of the power assembly).
4. Insert the handle and align the holes in the handle with the holes
in the power assembly. (Make sure that the recesses in the handle
are aligned with the screw holes in the power assembly for proper
placement of the handle)
5. Replace and tighten the hexagonal socket screws in their original
sockets. (The screws should tighten easily if properly aligned
(hardware kit C)
Keep out of reach from children!