Gardena PowerMax 32/18V P4A Mode D'emploi page 13

v Only start the mower with an upright standed handle.
v Do not overload the mower.
v Never operate the product when you are tired, ill or under the influence of
alcohol, drugs, or medicine.
2. ASSEMBLY
DANGER!
Cutting injury due to the blade!
Risk of cut injury due to accidental starting.
v Use gloves.
v Wait for the blade to stop.
v Remove the safety key.
2.1 To assemble the lower handlebars [ Fig. A1 ]:
1. Push both lower handlebars
Make sure that the handlebars are completely in place and the holes of
the handlebars are inline up with the holes of the openings in the
mower.
(3)
2. Put both wing screws
3. Tighten both wing screws
Make sure that the wing screws are completely tightened.
2.2 To assemble the upper handlebar [ Fig. A2 ]:
(4)
The upper handlebar can be assembled to the lower handlebars
3 positions to adjust the height.
Working position:
2.2.1
v Adjust the height of the handlebar so that you are in an upright position
when using the mower.
Position
Lower hole
Middle hole
Upper hole
(4)
1. Put the upper handle on the lower handlebars
Make sure that the handles are completely in place and the desired
holes are inline.
2. Push both screws (5) through the holes.
3. Put both washers (6) and both wing nuts
4. Tighten both wing nuts (7)
2.3 To attach the cable to the handlebar [ Fig. A3 ]:
1. Attach the clamps (9) to the holes provided for them on the
handlebar (1) .
2. Attach the cable (8) to the clamps
Make sure that the cable is not trapped between the handlebar and
the mower, otherwise the cable may be damaged.
2.4 To assemble the grass catcher box [ Fig. A4 / A5 ]:
(10)
1. Slide the tongue from behind into the connectors
catcher box until the connections audibly engages.
Make sure that all connectors are engaged.
2. First push the catcher box handle
(13)
cover .
3. Then push the catcher box handle
(13)
cover until the connections audibly engages.
Make sure that all connectors are engaged.
3. OPERATION
DANGER!
Cutting injury due to the blade!
Risk of cut injury due to accidental starting.
14632-20.960.02.indd 13 14632-20.960.02.indd 13
(1) into the openings (2) in the mower.
(2)
in the holes of the openings in the mower.
(3)
.
Height of the handle above the ground
91 cm
94 cm
97 cm
(1)
.
(7) on the screws (5)
.
(9) on the handlebar (1) .
(11)
on the grass
(12) at the back into the catcher box
(12) at the front into the catcher box
v Use gloves.
v Wait for the blade to stop.
v Remove the safety key.
3.1 To charge the battery [ Fig. O1 / O2 / O3 ]:
CAUTION!
The voltage of the power source must match the voltage specified on
the rating plate of the charger.
v Note the mains voltage.
For the GARDENA Battery Mower Art. 14632-55 there is no battery
and no charger in the scope of delivery.
Thanks to the intelligent charging process, the charge condition of the
battery is automatically detected and then charged up with the optimal
charge current depending on battery temperature and voltage.
In this way, the battery is treated with care and remains permanently fully
charged when it is stored in the charger.
(18)
1. Open the cover
2. Push the locking button
(D)
holder .
3. Connect the battery charger
4. Slide the battery charger
When the battery charge indicator
the battery is being charged.
(1)
in
When the battery charge indicator
nently green the battery is completely charged
(Charging time, see 7. TECHNICAL DATA).
5. Examine the charge status regularly while you charge.
6. When the battery
connected from the charger
3.2 Meaning of the indication elements:
3.2.1 Indication on the charger [ Fig. O3 ]:
Flashing of the Battery The charging procedure is indicated by flashing of the battery charge
(Lc)
Charge Indicator indicator
Note: The charging procedure is only possible when the battery
temperature is within the allowable charging temperature range,
see 7. TECHNICAL DATA.
Continuous Lighting
Continuous lighting of the battery charge indicator
.
of the Battery
the battery is fully charged or that the temperature of the battery is
Charge Indicator (Lc)
not within the allowable charging temperature range and can therefore
not be charged.
When the battery is not inserted, continuous lighting of the battery
charge indicator
socket outlet and that the battery charger is ready for operation.
3.2.2 Battery charge status indication
[ Fig. O4 ]:
After starting the product, the battery charge status indication
is displayed for 5 seconds.
Battery charge status indication
(L1) (L2) (L3)
, and light green
(L1) (L2)
and light green
(L1)
lights green
(L1)
blinks green
If the LED (L1) blinks green, the battery must be charged.
(Wp)
If the error LED is lighting or blinking
see 6. TROUBLESHOOTING.
3.2.3 Eco button [ Fig. O4 ]:
The Eco mode reduces the motor speed to 3100 rpm for a maximum
battery lifetime.
3.2.3.1 To activate the Eco mode:
v Push the Eco button
The Eco mode is activated and the LED
(D)
of the battery holder .
(A) (B)
and remove the battery
(C)
into a mains socket.
(C) (B)
onto the battery .
(Lc) at the charger blinks green
(Lc) at the charger lights perma-
(B)
is completely charged, the battery
(C) .
(Lc)
.
(Lc)
indicates that the mains plug is inserted in the
(P) on the product
Battery charge status
67 – 100 % charged
34 – 66 % charged
11 – 33 % charged
0 – 10 % charged
(e)
on the control panel.
(Le) lights.
from the battery
(B)
can be dis-
(Lc)
indicates that
(P)
13
25.07.22 10:57 25.07.22 10:57