EINHELL 15.440.90 Mode D'emploi page 13

Anleitung NSG 270 F_SPK1:Anleitung NSG 270 F_SPK1
Please follow the operating instructions, as described
below:
Important!
The mains plug may only be replaced by a
trained electrician.
Please observe the following instructions in order to
avoid the risk of fire, electric shock or personal
injuries.
Never use the appliance with a rated voltage of
400 V if the appliance is set to 230 V. Caution:
Fire risk!
Please disconnect the appliance from the power
supply before setting the rated voltage.
Adjusting the rated voltage during operation of the
welding set is strictly prohibited.
Before operating the welding set, please ensure
that the rated voltage selected on the appliance
complies with that of the power source.
7. Welding preparations
Connect the earth terminal (2) direct to the part to be
welded or to the support on which the part is resting.
Ensure that the earth terminal is in direct contact with
the part to be welded. You should therefore avoid
coated surfaces and/or insulated materials. The
electrode holder cable has a special clamp at one
end, which is used to secure the electrode. The
welding safety shield must be used at all times for
welding. It protects your eyes from the radiation
emitted by the arc and nevertheless enables you to
watch the welding process.
8. Welding
After you have made all the electrical connections for
the power supply and for the welding circuit, you can
proceed as follows:
Insert the unsheathed end of the electrode into the
electrode holder (1) and connect the earth terminal
(2) to the part you wish to weld.
Ensure that a good electric contact is made.
Switch on the welding set at the switch (4) and set
the welding current using the hand wheel (3) to suit
the electrode you wish to use.
Hold the safety shield in front of your face and rub
the tip of the electrode on the part you wish to weld
as if you were striking a match. This is the best
method of igniting the arc.
Check that you have the correct electrode and
current strength on a test part.
10.01.2007
All manuals and user guides at all-guides.com
Electrode (Ø mm):
2,5
3,2
4
5
Important!
Do not dab the workpiece with the electrode since it
could be damaged, making it more difficult to ignite
the arc.
As soon as the arc has ignited, attempt to keep it a
distance from the workpiece equivalent to the
diameter of the electrode.
This distance should be kept as constant as possible
during the welding process. The angle of the
electrode in the direction in which you are working
should be 20/30°.
Important!
Always use tongs to remove spent electrodes and to
move parts that you have just welded. Please note
that the electrode holder (1) must always be put
down so that it is insulated after you have completed
the welding work.
Do not remove the slag until the weld has cooled.
If you want to continue a weld after an interruption,
the slag from your initial attempt must first be
removed.
9. Overheating guard
The welding set is fitted with an overheating guard
that protects the welding transformer from
overheating. If the overheating guard trips, the
control lamp (5) on your set will be lit. Allow the
welding set to cool for a time.
10. Socket (12)
The welder has a 230 V/50 Hz socket on the back
side protected by a 6 A overload switch (11). The
overload switch (12) actuates if the socket (11) is
overloaded. Following the cool down phase, the
socket (12) can be reactivated using the overload
switch (11). The socket is designed for electric tools
with a maximum power consumption of 600 W.
Important!
Do not use tools during welding work.
7:59 Uhr Seite 13
GB
Welding current (A)
60 – 110 A
80 - 160 A
120 - 200 A
160 - 250 A
13