Publicité
Les langues disponibles
Les langues disponibles
Installation Instructions
Prepare Location
• It is recommended that the vent system be installed before
hood is installed.
• Before making cutouts, make sure there is proper clearance
within the ceiling or wall for exhaust vent.
• Check your ceiling height and the hood height maximum
before you select your hood.
1.
Disconnect power.
2.
Determine which venting method to use: roof, wall, or
nonvented.
3.
Select a flat surface for assembling the range hood. Place
covering over that surface.
WARNING
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR
INJURY TO PERSONS, OBSERVE THE FOLLOWING
4.
Using 2 or more people, lift range hood onto covered surface.
Range hood mountig screws
installation
1.
Determine and mark the centerline on the wall where the
canopy hood will be installed. Disconnect power.
2.
Select a mounting height between a minimum of 24" (60.9
cm) for an electric cooking surface, a minimum of 30" (76.2
cm) for a gas cooking surface, and a suggested maximum
of 36" (91.4 cm) above the range to the bottom of the hood.
Mark a reference line on the wall.
3.
Tape template in place, aligning the template centerline
and bottom of template with hood bottom line and with the
centerline marked on the wall.
D
I R
L L
2
T (
W
O
3 )
1 /
" 6
P
L I
O
T
H
O
S E
L
T
H
H
o
i r
o z
n
a t
L l
n i
e
A. Centerline
B. Fastener locations
C. Mounting height reference (hood bottom line)
A
O
R
U
G
H
T S
U
D
S
O
R
E R
A
R
W
A
L L
S
U
P
P
O
T R
E R
A
R
W
A
L L
M
O
U
N
T
N I
G
E T
M
L P
A
E T
C
L
A
L
G I
N
B
O
T T
O
M
E
D
G
E
W
T I
H
E P
N
C
L I
L
N I
E
N I
D
C I
A
T
N I
G
B
O
T T
O
M
O
F
T
H
E
H
O
O
D
n I
t s
l l a
t a
o i
n
H
e
g i
t h
B
C
4.
Mark centers of the fastener locations through the template to
the wall.
IMPORTANT: All screws must be installed into wood. If there
is no wood to screw into, additional wall framing supports
may be required.
5.
Remove the template.
6.
Drill
⁄
" (4.8 mm) pilot holes at all locations where screws are
3
16
being installed into wood.
7.
Install the 2 - 5 x 45 mm mounting screws. Leave a
mm) gap between the wall and the back of the screw head to
slide range hood into place.
1⁄4"
(6.4 mm)
Vent cover bracket installation
1.
Attach vent cover bracket to wall flush to the ceiling using 2 -
5 x 45 mm screws.
A
B
A. 8 x 40 mm drywall anchors
B. Centerline on wall
C. Vent cover support bracket
D. 5 x 45 mm screws
Complete Preparation
1.
Determine and make all necessary cuts in the wall for the vent
system. Install the vent system before installing the hood. See
"Venting Requirements" section.
2.
Determine the required height for the home power supply
cable and drill a 1¼" (3.2 cm) hole at this location.
3.
Run the home power supply cable according to the National
Electrical Code or CSA Standards and local codes and
ordinances. There must be enough ½" conduit and wires
from the fused disconnect (or circuit breaker) box to make the
connection in the hood's electrical terminal box.
NOTE: Do not reconnect power until installation is complete.
4.
Use caulk to seal all openings.
5.
Remove plastic bag with styrofoam located behind the blower
motor from inside the hood.
5
⁄
"(6.4
1
4
C
D
Publicité
