Publicité
Les langues disponibles
Les langues disponibles
Liens rapides
Page 1 of 11
FITTING INSTRUCTIONS FOR RAD0242 RADIATOR GUARD
Please note that the way the kit is packed does not necessarily represent the way of mounting to the bike
Please note that in cases where kits are packed with rubber washers holding the components onto the bolt – the rubber washers should be thrown away!
T
HE PARTS SHOWN MAY BE REPRESENTATIVE ONLY
Digital copies of these instructions are available to download from
Tel: +44 (0)1420 89007 Fax: +44 (0)1420 87301
KAWASAKI NINJA 125/ Z 125 2019
THIS KIT CONTAINS THE ITEMS PICTURED AND LABELLED BELOW.
DO NOT PROCEED UNTIL YOU ARE SURE ALL PARTS ARE PRESENT.
GENERAL TORQUE SETTINGS
M4 BOLT = 8Nm
M5 BOLT = 12Nm
M6 BOLT = 15Nm
M8 BOLT = 20Nm
M10 BOLT = 40Nm
TOOLS REQUIRED
•
Socket set to include 10mm socket and wrench or spanner.
•
Set of metric Allen keys.
In This Kit There Should Be
•
1 x Radiator Guard (RAD0242).
•
4 x 100mm Lengths of self-adhesive Foam.
Unit 1, Shelley's Lane, East Worldham, Alton, Hampshire, GU34 3AQ
(
FOR CLARITY OF INSTRUCTIONS ONLY
•
Philips driver.
•
4 x Cable Ties
R&G
www.rg-racing.com
RAD0242
)
www.rg-racing.com
Email:
info@rg-racing.com
Publicité
Manuels Connexes pour R&G RAD0242
Sommaire des Matières pour R&G RAD0242
- Page 1 Page 1 of 11 RAD0242 FITTING INSTRUCTIONS FOR RAD0242 RADIATOR GUARD KAWASAKI NINJA 125/ Z 125 2019 THIS KIT CONTAINS THE ITEMS PICTURED AND LABELLED BELOW. DO NOT PROCEED UNTIL YOU ARE SURE ALL PARTS ARE PRESENT. Please note that the way the kit is packed does not necessarily represent the way of mounting to the bike Please note that in cases where kits are packed with rubber washers holding the components onto the bolt –...
- Page 2 Page 2 of 11 RAD0242 Picture 1 Picture 2 Picture 3 Picture 4 Picture 5 Picture 6 R&G Unit 1, Shelley’s Lane, East Worldham, Alton, Hampshire, GU34 3AQ Tel: +44 (0)1420 89007 Fax: +44 (0)1420 87301 www.rg-racing.com Email: info@rg-racing.com...
- Page 3 Page 3 of 11 RAD0242 Picture 7 Picture 8 Picture 9 Picture 10 Picture 11 Picture 12 R&G Unit 1, Shelley’s Lane, East Worldham, Alton, Hampshire, GU34 3AQ Tel: +44 (0)1420 89007 Fax: +44 (0)1420 87301 www.rg-racing.com Email: info@rg-racing.com...
- Page 4 Page 4 of 11 RAD0242 Picture 13 Picture 14 Picture 15 Picture 16 Picture 17 Picture 18 R&G Unit 1, Shelley’s Lane, East Worldham, Alton, Hampshire, GU34 3AQ Tel: +44 (0)1420 89007 Fax: +44 (0)1420 87301 www.rg-racing.com Email: info@rg-racing.com...
- Page 5 Page 5 of 11 RAD0242 Picture 19 Picture 20 Picture 21 Picture 22 Picture 23 Picture 24 R&G Unit 1, Shelley’s Lane, East Worldham, Alton, Hampshire, GU34 3AQ Tel: +44 (0)1420 89007 Fax: +44 (0)1420 87301 www.rg-racing.com Email: info@rg-racing.com...
- Page 6 Page 6 of 11 RAD0242 FITTING INSTRUCTIONS • To fit the radiator guard to the bike, cut the foam strip provided into 10mm wide pieces and stick them to the back of the radiator guard frame, so that they sit between the radiator guard and the radiator.
- Page 7 Page 7 of 11 RAD0242 NOTICE DE MONTAGE POUR RAD0242 GRILLE DE PROTECTION RADIATEUR KAWASAKI NINJA 125/ Z 125 2019 Le kit contient les articles exposés ci-dessous, vérifier que toutes les pièces soient présentes avant de procéder au montage. La façon dont le kit est emballé ne correspond pas forcément à la façon de monter les pièces sur la moto.
- Page 8 Page 8 of 11 RAD0242 NOTICE DE MONTAGE • Pour monter la grille de protection sur la moto, couper la mousse autocollante fournie en bandeaux de 10mm puis collez les au bas du cadre de protection radiateur, de façon à ce qu’ils se placent entre la grille de protection radiateur et le radiateur.