Télécharger Imprimer la page

R&G RAD0193BK Instructions De Montage page 6

Publicité

le réservoir avec le clip en métal) puis tordre l'avant pour le libérer des clips en
partie difficile à enlever, visible sur les photos 11, 12, 13 & 14.
Répéter les 2 étapes du dessus pour enlever le cache interne du coté gauche de la moto.
Enlever le boulon qui fixe le bas du radiateur en place, voir photo 15.
Mettre la protection radiateur R&G en place, en veillant à ce que les 2 supports supérieurs se
placent à l'intérieur des 2 supports supérieurs de radiateur.
Remettre le boulon d'origine dans le trou de fixation inférieur de la protection radiateur, puis dans
le support radiateur avant de serrer légèrement, voir photo 16.
Insérer un boulon M6 x 16mm fans le trou de fixation du support de fixation radiateur puis dans le
trou de fixation de la protection radiateur, avant d'insérer une rondelle M6 et un écrou sur
l'extrémité du filetage, voir photos 17 & 18, avant de serrer légèrement.
Répéter la dernière étape pour positionner le boulon restant, la rondelle et l'écrou dans les points
de fixation de l'autre coté de la moto, voir photo 19, avant de serrer légèrement.
Veiller à ce que la grille de protection radiateur soit correctement montée avant de serrer les 3
boulons de fixation.
Remonter les 2 caches plastic noirs.
Ces instructions de montage sont disponibles au téléchargement sur
The catalogue description and any exhibition of samples are only broad indications of the Products and R&G may make design changes which do not
diminish their performance or visual appeal and supplying them in such state shall conform to the order. The Buyer acknowledges no representation or
warranty (other than as to title) has been given or will apply to the Products other than those in R&G's order or confirmation and the Buyer confirms it
has chosen the Products as being of merchantable quality and suitable for its particular purposes. Where R&G fits the Products or undertakes other
services it shall exercise reasonable skill and care and rectify any fault free of charge unless the workmanship has been disturbed. The Buyer is
responsible for ensuring that the warranty on the motorcycle is not affected by the fitting of the Products. On return of any defective Products R&G shall
at its option either supply a replacement or refund the purchase money but shall not be liable if the Products have been modified or used or maintained
otherwise than in accordance with R&G's or manufacturer's instructions and good engineering practice or if the defect arises from accident or neglect.
Other than identified above and subject to R&G not limiting its liability for causing death and personal injury, it shall not be liable for indirect or
consequential loss and otherwise its liability shall be limited to the amounts paid by the Buyer for the Products or the fitting or service concerned. These
terms do not affect the Buyer's statutory rights.
Returns must be pre-authorised (if not pre-authorised the return will be rejected). Goods may only be returned direct to us if they were purchased direct
from us (customer must prove if necessary). Otherwise to be returned to original vendor. Goods must be in re-sellable condition, in the opinion of R&G
Racing. All returns are subject to a 25% restocking and handling fee (25% of the gross value exc. P&P – at the prevailing price at time of purchase). The
customer must pay any and all carriage charges. No returns of discontinued products, unless within 14 days of purchase. This policy does not affect your
statutory rights and does not refer to faulty goods.
Unit 1, Shelley's Lane, East Worldham, Alton, Hampshire, GU34 3AQ
Tel: +44 (0)1420 89007 Fax: +44 (0)1420 87301
ISSUE 2 20/08/2015 (AR)
CONSUMER NOTICE
R&G RACING RETURNS POLICY (NON-FAULTY GOODS)
R&G Racing
www.rg-racing.com
plastics.
www.rg-racing.com
Email:
info@rg-racing.com
C'est une

Publicité

loading