Bestway 58775 Manuel Du Propriétaire page 4

SETUP
CHECK LIST
To check the parts list inside the manual. Verify that the equipment components represent the model that you had intended to purchase. In case of
any damaged or missing parts at the time of purchase, visit our website bestwaycorp.com/support. Drawings are for illustration purposes only. May
not reflect actual product. Not to scale.
PRODUCT SPECIFICATIONS
Maximum chlorine production per hour:
Sand filter/Filter pump flow range:
Salt concentration:
Water temperature:
Ambient temperature:
Compatible with max water capacity:
RECOMMENDATIONS BEFORE INSTALLATION
• The chlorinator must be installed at the last position of the water circulation pipe (down the direction of the water flow) as shown in "1a. and 1b.".
• Only use sodium chloride (NaCl) salt with a purity of at least 99.8% to fully dissolve it.
• Too low salt purity will reduce the efficiency of the chlorinator and result in low chlorine production. High salt purity may produce a salty taste to
the pool water and it may cause corrosion to metal fixtures and fittings in the pool.
• The "Pool Salt Table" shows the correct amount of salt required. Refer to the different quantity of water. The salt in the pool will not automatically
decrease.
• Only when the pool water is lost will the salt in the water decrease, and the evaporation of water will not cause the salt to decrease.
Pool capacity
(gal)
2000
4000
6000
8000
10000
12000
14000
15000
If the device shows error E2, it is necessary to reduce the salt concentration: Drain about 20% of the pool water, and then refill with clean water.
Wait 1 hour, and if the error still remains, repeat the operation until the E2 error disappears.
In case the quantity of water of your pool is not listed in the "pool salt table", follow the below formula to calculate the correct quantity of salt to add
to the pool to reach the 3000 ppm of salt concentration, or in case the E1 error appears on the display.
The amount of salt added for the first time:
(lb)
Water capacity(gal)
*0.025
USING THE CHLORINATOR
12 g/h
330-3000 gal/h
3000 ppm (3 g/L）
10-36°C
5-45°C
15000 gal (56775 L)
The amount of salt added for the
first time 3.0 g/L (3000 ppm)
(l) (lb)
7570 50
15140 100
22710 150
30280 200
37850 250
45420 300
52990 350
56775 375
(kg)
Water capacity(l)
*0.003
Code
Icon
number
1
2
3
4
5
NO FLOW
6
Pool Salt Table
(kg)
23
45
68
91
114
136
159
170
The amount of salt that needs to be added if the "E1"
(lb)
Water capacity(gal)
*0.0084
Name
Power button Press and hold for 3s to turn on/off the chlorinator
Press and hold for 3s to lock/unlock, and press quickly
Timer button
to adjust working time
When the lock indicator is unlit, the product is unlocked.
Lock indicator If no button is pressed, the product will automatically
lock after 1 minute and the Lock indicator will turn red.
Red: The salt concentration is too high, part of the salt
should be removed from the pool water. Display shows: E2;
Salt
concentration
Green: The salt concentration is at the optimal level;
indicator
Yellow: The salt concentration is too low and salt needs to
be added to the pool water. Display shows: E1.
Water flow
Shows red, no water flow or insufficient water flow
status indicator
Displays running time/remaining time/fault code
Digital Display
Power-on state/standby mode
4
Display code "E1" the amount of
salt that needs to be added
(lb)
17
33
50
66
83
100
116
125
error code displays:
(kg)
Water capacity(l)
*0.001
Illustrate
(kg)
8
15
23
30
38
45
53
57