Char-Broil 14101480-A2 Guide Des Produits page 8

Ignitor Lighting
• Do not lean over appliance while lighting.
1. Turn ON LP gas cylinder.
2. Press and turn the control knob to
3. Turn ROTARY IGNITOR knob rapidly.
4. If ignition does not occur in 5 seconds, turn the burner control
knob OFF, wait 5 minutes, and repeat lighting procedure.
If ignition still does not occur, follow match-lighting
instructions.
WARNING
Turn control knob and LP cylinder OFF when not in use.
CAUTION
If ignition does NOT occur in 5 seconds, turn the
control knob (OFF), wait 5 minutes and repeat the
lighting procedure. If the burner does not ignite with the
valve open, gas will continue to flow out of the burner
and could accidently ignite with risk of injury.
Match-Lighting
• Do not lean over appliance while lighting.
1. Turn ON LP cylinder.
2. Swing match hole plate to expose match lighting hole. Place
lit match into match lighting hole of appliance as pictured
below. Make sure lit match is placed inside hole and near
burner.
3. Push in and turn control knob to
stays lit.
4. Once lit, swing match hole plate back to cover up match
lighting hole. Caution: Plate maybe hot.
Control
Knob
View is from side of
Be sure burner lights and
Match
Match Hole
Lighting Hole
Plate
Match
Lighting
Match
Hole
Hole
Swing Plate to
Plate
expose
Matchlighting
Hole
Swing Plate
to expose
Matchlighting
Hole
Match
appliance
Burner Flame Check
• Light burner. Looking through viewing hole on top of appliance,
you should see the flame height as shown below. Turn control
knob from to OFF. The Flame height should decrease
and then go out. Always check flame prior to each use. If only
low flame is seen refer to "Sudden drop or low flame" in the
Troubleshooting Section.
Turning Appliance Off
• Turn control knob to
turning hand-wheel clockwise to a full stop.
Ignitor Check
• Turn gas off at LP cylinder. Turn ignitor knob. "Click" should
be heard each time at electrode. See "Troubleshooting" if no
click or spark.
Valve Check
• Important: Make sure gas is off at LP cylinder before
checking valve. Knob locks in
valve, first push in knob and release, knob should spring
back. If knob does not spring back, replace valve assembly
before using this appliance. Turn knob to
back to OFF position. Valve should turn smoothly.
Hose Check
• Before each use, check to see if hose is cut, worn or kinked.
Replace damaged hose before using applaince. Use only
valve/hose/regulator specified by manufacturer.
Normal
Hose
General Appliance Cleaning
• Meat Thermometer: Do not immerse or soak in water. Wash
with warm soapy water and wipe dry.
• Do not mistake brown or black accumulation of grease and
smoke for paint. Interiors are not painted at the factory (and
should never be painted). Apply a strong solution of detergent
and water or use a unit cleaner with scrub brush on insides of
appliance lid and bottom. Rinse and allow to completely air dry.
Do not apply a caustic grill/oven cleaner to painted
surfaces. A black surface improves the appliances
performance.
• Plastic parts: Wash with warm soapy water and wipe dry.
Do not use citrisol, abrasive cleaners, degreasers or a
concentrated grill cleaner on plastic parts. Damage to and
failure of parts can result.
• Painted surfaces: Wash with mild detergent or non-abrasive
cleaner and warm soapy water. Wipe dry with a soft non-
abrasive cloth.
8
High Flame
OFF position. Turn LP cylinder off by
OFF position. To check
position then turn
Kinked
Hose
Low Flame