JB Systems CD 670 Mode D'emploi page 7

ENGLISH
 PITCH BEND buttons: The speed increases or decreases respectively as long as
the PITCH BEND+ or PITCH BEND- buttons are pressed.
 JOG WHEEL: During play mode the JOG WHEEL will temporarily bend the pitch of
the music by turning the JOG WHEEL clockwise to speed up or counterclockwise to
slowdown. The rotation speed the JOG WHEEL determines the percent of pitch
bend.
 PLAYING/RECORDING CD-R and CD-RW:
Apart from normal audio CD's the CD670 can play both CD-R (CD recordable) and CD-
RW (CD rewriteable). Please note that you should always use the "disc at once" and
"track at once" disc writing options! Although the CD670 is capable of reading CD-R and
CD-RW recorded at higher speeds, we suggest not using recording speeds more than
x12 to increase readability. Always buy good quality brands for CD-R and CD-RW!
If the disc is multi session, it will only play the first session.
ABOUT LOOPS:
 CREATE A LOOP:
While a track is playing, press R.CUE/LOOP IN button to program the starting point of
the loop. Now press the OUT/EXIT button to program the endpoint of the loop. The
seamless loop starts playing at once. (With some practice you will be able to create
perfect loops!) While the loop is playing, you can press the OUT/EXIT button again to
exit the loop and continue the rest of the track.
It is possible to program a new loop, even when the current loop is still playing. While the
loop is playing, simply press the R.CUE/LOOP IN button to set the starting point of the
new loop. Now enter the endpoint by pressing the OUT/EXIT button. Your new loop is
programmed and playing.
 RESTART A LOOP:
This can be done in 3 ways:
 When a loop is programmed and you left it by pressing the OUT/EXIT button, just
press RELOOP to restart the loop.
 When a loop is programmed and you left it by pressing the OUT/EXIT button, just
press OUT/EXIT again to restart the loop. The point where you pressed OUT/EXIT is
now programmed as the new endpoint of the loop.
 When the loop is still playing, press the RELOOP button to restart the loop
immediately. You can repeat this several times to create a "Stutter" effect.
 EDIT A LOOP:
When a loop is programmed, press the RELOOP/STUTTER button for about 2 seconds
to enter "loop edit" mode. While the loop is seamlessly playing, the display shows the
time information of the loop endpoint. Use the jog wheel to set the new loop endpoint. To
make things very easy you can hear your modifications to the loop endpoint
continuously. When the loop is perfect, press the LOOP OUT button to save the new
loop endpoint.
JB SYSTEMS®
OPERATION MANUAL
9/67
ENGLISH
SPECIFICATIONS
Power Supply:
Power Consumption:
Output level:
Frequency response:
THD + noise (20kHz LPF):
S/N Ratio (IHF-A):
Short access time (next track):
Long access time (track 1  20):
Laser Pickup:
Electronic tracking:
Digital output:
Operation temperature:
Humidity:
Dimensions:
Weight:
You can download the latest version of this user manual on our website:
CD670 JB SYSTEMS®
AC 230 V, 50Hz
21W
2,0Vrms +/0.5dB @ 1kHz, 0dB
20-20.000Hz (+/-0,4dB)
0,01% @ 1kHz, 0dB
>92dB @ 1kHz, 0dB
<2sec
<4sec
Sony KSM-213CCM 3spot detection 780nm
Full automatic digital tracking.
0,5Vpp +/-0,1 (load = 75Ω)
5°C to 35°C
25 to 85% RH (non condensing)
Main unit 482(W) x 88,8(H) x 262,5(D) mm
Control unit 482(W) x 88,8(H) x 94(D) mm
Main unit 5,0kg
Control unit 1,8kg
Every information is subject to change without prior notice
10/67
OPERATION MANUAL
www.beglec.com
CD670