Controls And Functions; Main Unit - Front; Main Unit - Rear - JB Systems CD 670 Mode D'emploi

ENGLISH
 The socket inlet shall remain operable for disconnection from the mains.
 The power cord should always be in perfect condition: switch the unit immediately off
when the power cord is squashed or damaged.
 Never let the power-cord come into contact with other cables!
 When the power switch is in OFF position, this unit is not completely disconnected from
the mains!
 In order to prevent electric shock, do not open the cover. Apart from the mains fuse there
are no user serviceable parts inside.
 Never repair a fuse or bypass the fuse holder. Always replace a damaged fuse with a
fuse of the same type and electrical specifications!
 In the event of serious operating problems, stop using the appliance and contact your
dealer immediately.
 Please use the original packing when the device is to be transported.
 Due to safety reasons it is prohibited to make unauthorized modifications to the unit.
INSTALLATION GUIDELINES:
 Placing and using the unit for long periods near heat-generating sources such as
amplifiers, spotlights, etc. will affect its performance and may even damage the unit.
 Take care to minimize shocks and vibrations during transport.
 The unit can be mounted in 19-inch racks. Attach the unit using the 4 screw holes on the
front panel. Be sure to use screws of the appropriate size. (screws not provided)
Take care to minimize shocks and vibrations during transport.
 When installed in a booth or flight case, please make sure to have good ventilation to
improve heat evacuation of the unit.
 To avoid condensation to be formed inside, allow the unit to adapt to the surrounding
temperatures when bringing it into a warm room after transport. Condense sometimes
prevents the unit from working at full performance.
 Choose the place where you put your installation very carefully. Avoid presence of heat
sources. Avoid places with vibrations or places that are dusty and humid.
 The player will work normally when installed on a surface with max. 15° inclination.
 Be very careful while handling CDs, do not touch them with wet or dirty hands.
 Discs that are dirty must be cleaned with special designed cloth and cleaning products.
 Do not use CDs that are badly damaged (scratched or deformed) they can damage your
appliance.
 To prevent fire or shock hazard, do not expose this appliance to rain or moisture.
 In order to prevent electric shock, do not open the top cover. If a problem occurs, contact
your dealer.
 Do not place metal objects or spill liquid inside the CD player. Electric shock or
malfunction may result.
 This CD player uses the semiconductor laser. To allow you to enjoy music at a stable
operation, it is recommended to use this in a room of 5°C – 35°C.
 The compact disc player should not be adjusted or repaired by anyone except properly
qualified service personnel.
 This unit may cause interference to radio and television reception.
CLEANING THE APPLIANCE:
Clean by wiping with a polished cloth slightly dipped with water. Avoid getting water inside
the unit. Do not use volatile liquids such as benzene or thinner which will damage the unit.
JB SYSTEMS®
OPERATION MANUAL
3/67
ENGLISH
CONNECTIONS
 Connect the mini-DIN cable between the control unit and the main unit (CD loader).
 Use the supplied cinch cables to connect the audio outputs of the CD player with the CD
inputs of your mixing unit.
 Also connect the 2 fader start cables if your audio mixer has fader start connections.
®
(Synq
 Connect the mains cable.

CONTROLS AND FUNCTIONS

MAIN UNIT - FRONT

1. POWER (Power ON/OFF switch): When the power switch is pressed, the power turns
on and the blue led is lit.
2. DISC TRAY: Use the OPEN/CLOSE buttons to open disc tray and put the CD in place.
If the tray is not closed after 60sec. It will close automatically to prevent damage.
3. OPEN/CLOSE button: press this button to open and close the disc tray. These
buttons are disabled during playback.

MAIN UNIT - REAR:

4. Control connector: use the supplied mini-DIN cable to connect this output to the
control unit.
5. Audio outputs: Output for the audio signals from each player. Use the supplied
cinch/cinch cables to connect these outputs to the CD/line inputs of your mixing unit.
6. Digital out socket: Use this connector to connect the digital signal (S/PDIF format) to
the input of a digital amplifier or digital recorder (ex. Mini disc)
7. Mains input: connect the CD player to the 230V AC mains, using the supplied power-
cord.
CD670 JB SYSTEMS®
®
or Pioneer compatible)
4/67
OPERATION MANUAL
CD670