Publicité
Les langues disponibles
Les langues disponibles
Liens rapides
AUTOMOTIVE PRODUCTS, INC.
MOUNT KIT
EQUIPO DE MONTAJE
OPTIONAL LIGHT
JEU DE MONTAGE
27-1725
MOLDED
SURE-GRIP
STEP
BOARDS
BOARDS
27-6130
27-0010
27-6135
27-0015
27-6530
27-0020
27-6140
27-0025
27-6145
27-6540
CONTENTS -
ITEM
QTY
1,2
2
STEP BOARD, PASSENGER (1) AND DRIVER (2) (SOLD SEPARATELY)
3
2
FRONT BRACKET
4
2
FRONT/CENTER BRACKET
5
2
REAR/CENTER BRACKET
6
2
REAR BRACKET
7
16
M8-1.25 X 30MM HEX HEAD BOLT
8
16
3/8" FLAT WASHER
9
16
3/8" LOCK WASHER
10
16
5/16-18 X .75" SQUARE HEAD BOLT
11
16
5/16" FLAT WASHER
12
16
5/16-18 LOCK NUT
1,2
2
ESTRIBOS, ACOMPAÑANTE (1) CONDUCTOR (2) (SE COMPRA SEPARADO)
3
2
SOPORTE DELANTERAS
4
2
SOPORTE DELANTERAS
5
2
SOPORTE TRASERAS
6
2
SOPORTE TRASERAS
7
16
PERNOS CON CABEZA HEXAGONAL M8-1.25 X 30MM
8
16
ARANDELAS PLANAS DE 3/8
9
16
ARANDELAS DE PRESIÓN DE 3/8
10
16
PERNOS CON CABEZA CUADRAD 5/16-18 X .75"
11
16
ARANDELAS DE PRESIÓN DE 5/16
12
16
TUERCA PRESIÓN DE 5/16-18
1,2
2
MARCHE-PIEDS, PASSAGER (1) ET CONDUCTEUR (2) (ACHETE
SEPAREMENT)
3
2
SUPPORT AVANT
4
2
SUPPORT AVANT/CENTRAL
5
2
SUPPORTS ARRIERE/CENTRAL
6
2
SUPPORTS ARRIERE
7
16
BOULON A TETE HEXAGONALE M8-1.25 X 30 MM
8
16
RONDELLE PLATE 3/8"
9
16
RONDELLE A FREIN DE 3/8"
10
16
BOULON A TETE CARREE 5/16-18 X .75 PO
11
16
RONDELLES PLATES 5/16 PO
12
16
ECROU A FREIN 5/16-18
STEP 1.
Remove contents from box and check for damage. Verify all parts are present. Read instructions completely before beginning. It is strongly
recommended to install the Sure Grip Gap Strip for these vehicle applications.
STEP 2.
Determine front, front center, rear center and rear brackets. Rear/center bracket has 1 identification hole and rear bracket has 2 identification
holes.
SEE FIGURE 1.
STEP 3.
Attach drivers side brackets to underside of body panel using two M8-1.25 x 30mm hex head bolts, 3/8" flat washers, and 3/8" lock washers per
bracket. Hand tighten.
STEP 4.
Insert square head bolts as shown (4 per slot, 8 per board).
attaching board to brackets (refer to Step 4) Run longer wire harness on passenger side.
STEP 5.
For Sure-Grip Running Boards, slide closure strip as shown. Set lights (if purchased) in appropriate location. Attach to Sure-Grip Running Board
as shown.
SEE FIGURE 2.
STEP 6.
Attach board to brackets as shown. Make sure board and brackets are properly aligned and tighten fasteners. Recommended torque values are
10 Ft.Lbs. For 5/16" hardware and 22 Ft.Lbs. For M8 hardware.
NOTE:
For lighted version of Molded Step Board, remove plastic cover from each end of under side of board. Proceed to Steps
7-8.
WARNING: INSTALLING LIGHT HARNESS REQUIRES SPLICING INTO VEHICLES ELECTRICAL SYSTEM. WESTIN RECOMMENDS
USING A PROFESSIONAL FOR THIS INSTALLATION. NOTE: AVOID AREAS OF EXCESSIVE HEAT, VIBRATION, PINCH
OR ROTATION WHEN SECURING HARNESS TO VEHICLE. CAUTION: ALWAYS USE A FUSED(+) POSITIVE SUPPLY
HINT:
Molded Step Boards: For longevity, check rubber seals before installation. Rubber grommets around red and blue wires going into rear
INSTRUCTIONS-INSTRUCCIONES-CONSIGNES
APPLICATION: 2007-08 TOYOTA TUNDRA DOUBLE CAB & CREW MAX
APLICACIÓN:
APPLICATION:
SURE-GRIP
KIT
27-6000
1
CONTENIDO
- CONTENU
/CENTRAL
/CENTRAL
"
"
"
SEE FIGURE 1.
.
Drill hole through plastic strip and run wires as shown.
SOURCE. UNDERCOAT SEAL FOR HARSH WEATHER.
TOYOTA TUNDRA DOBLECABINA & CABINA MÁXIMO
TOYOTA TUNDRA DOUBLE CABINE & CABINE MAXIMUM
SEE FIGURES 3 AND 4 NOTE:
SEE FIGURE 6.
WO:
3
4
TOOLS-HERRAMIENTA-OUTILS
1/2" SOCKET
1/2" WRENCH
13MM SOCKET
13MM WRENCH
RATCHET
RATCHET EXTENSION
TORQUE WRENCH
DADO DE 1/2"
LLAVE DE TUERCAS DE 1/2"
DADO DE 13MM
LLAVE DE TUERCAS DE 13MM
MANERAL
MANERAL EXTENSION
LLAVE DE TORQUE
DOUILLE 1/2"
CLE 1/2"
DOUILLE 13MM
CLE 13MM
CLIQUET
RALLONGE DE
CLIQUET
CLE DE COUPLE
.
For lighted boards, run wiring harness prior to
SEE FIGURE 5.
75-0765 REVISION D 6/30/08
, MOD. 2007-08
, 2007-08
5
6
Publicité
Manuels Connexes pour Westin 27-1725
Sommaire des Matières pour Westin 27-1725
- Page 1 For lighted version of Molded Step Board, remove plastic cover from each end of under side of board. Proceed to Steps 7-8. WARNING: INSTALLING LIGHT HARNESS REQUIRES SPLICING INTO VEHICLES ELECTRICAL SYSTEM. WESTIN RECOMMENDS USING A PROFESSIONAL FOR THIS INSTALLATION. NOTE: AVOID AREAS OF EXCESSIVE HEAT, VIBRATION, PINCH OR ROTATION WHEN SECURING HARNESS TO VEHICLE.
- Page 2 FINISH PROTECTION Westin products have a high quality finish that must be cared for like any other exposed finish on the vehicle. Protect the finish with a non-abrasive automotive wax, (e.g. Pure Carnauba) on a regular basis. The use of any soap, polish or wax that contains an abrasive is detrimental, as the compounds scratch the finish and open it to corrosion.
- Page 3 PROTECTION DE LA FINISSION Les produits Westin ont une finission de haute qualité qui requiert des soins, comme toute autre finission du véhicule exposée aux éléments. Protégez la finission à l’aide d’une cire non-abrasive (par exemple, Pure Carnauba) de façon régulière. L ’usage de tout savon, pâte à polir ou cire contenant un abrasif est nuisible, puisque les composantes strient la finission et la laissent vulnérable à...
- Page 4 7 9 8 7 9 8 7 9 8 7 9 8 FIGURE 1 INSTALLATION VIEW OF DRIVER SIDE SHOWN, PASSENGER SIDE OPPOSITE FIGURA 1 VISTA DE LA INSTALACIÓN DEL LADO DEL CONDUCTOR OPUESTO AL LADO DEL ACOMPAÑANTE FIGURE 1 ILLUSTRE: COTE CONDUCTEUR, EN FACE: COTE PASSAGER FIGURE 2 FIGURA 2...