Westin 27-1615 Manuel D'instructions

AUTOMOTIVE PRODUCTS, INC.
MOUNT KIT
EQUIPO DE MONTAJE
JEU DE MONTAGE
27-1615
STEP BOARD
ESTRIBOS
MARCHEPIED
27-6000 27-6130 27-6135
EXT. CAB. 27-0000 27-0005
DBL. CAB 27-0010 27-0015
CONTENTS -
ITEM QTY
1 2 STEP BOARD (PURCHASED SEPARATELY)
2,3 2 FRONT BRACKET, PASSENGER (2) AND DRIVER (3)
4,5 4 CENTER / REAR BRACKET, PASSENGER (4) AND DRIVER (5)
6 12 M8-1.25 X 25MM HEX HEAD BOLT
7 12 5/16-18 X .75" SQUARE HEAD BOLT
8 24 5/16" FLAT WASHER
9 12 5/16-18 LOCK WASHER
10 12 5/16-18 LOCK NUT
1 2 ESTRIBOS (SE COMPRAN POR SEPARADO)
2,3 2 PIEZAS DE SUJECIÓN DELANTERAS, LADO DEL ACOMPAÑANTE (2) Y EL
CONDUCTOR (3)
4,5 4 PIEZAS DE SUJECIÓN CENTRAL / TRASERAS, LADO DEL ACOMPAÑANTE (4)
Y EL CONDUCTOR (5)
6 12 PERNOS CON CABEZA HEXAGONAL DE M8-1,25 X 25MM
7 12 PERNOS CON CABEZA CUADRADA DE 5/16-18 X ,75
8 24 ARANDELAS PLANAS DE 3/8"
9 12 ARANDELAS DE PRESIÓN DE 3/8"
10 12 TUERCA PRESIÓN DE 5/16-18
1 2 MARCHEPIED (VENDU SÉPARÉMENT)
2,3 2 SUPPORTS AVANT, PASSAGER (2) ET CONDUCTEUR (3)
4,5 4 SUPPORTS CENTERAL / ARRIERE, PASSAGER (4) ET CONDUCTEUR (5)
6 12 BOULONS A TETE HEXAGONALE M8-1,25 X 25MM
7 12 BOULON A TETE CARREE 5/16-18 X .75 PO
8 24 RONDELLES PLATES 5/16 PO
9 12 RONDELLES A FREIN 5/16 PO
10 12 ECROU A FREIN 5/16-18
STEP 1. Remove contents from box and check for damage. Verify all parts are present. Read and understand instructions before
beginning.
STEP 2. Attach mounting brackets as shown. See Figures 1 and 2.
Insert square head bolts as shown (3 per slot, 6 per Step board/Running board). See Figures 4 and 5.
STEP 3.
Step board/Running board, run wiring harness prior to attaching step board to brackets (Refer to Step 6). See Figures 4, 5 &
8). Run longer wire harness on passenger side.
STEP 4. For Aluminum Running boards, if desired, slide closure strip as shown. Set lights (if included) in appropriate location. Attach
to running board as shown. See Figure 3. Drill hole through plastic strip and run wires as shown. See Figure 6.
STEP 5. Attach Step board / Running board to brackets as shown. Align and tighten. See Figure 7.
Step board, remove plastic cover from each end of under side of Step board. Proceed to Steps 6-7.
WARNING: INSTALLING LIGHT HARNESS REQUIRES SPLICING INTO VEHICLES ELECTRICAL SYSTEM. WESTIN
RECOMMENDS USING A PROFESSIONAL FOR THIS INSTALLATION. NOTE: AVOID AREAS OF
EXCESSIVE HEAT, VIBRATION, PINCH OR ROTATION WHEN SECURING HARNESS TO VEHICLE.
CAUTION: ALWAYS USE A FUSED(+) POSITIVE SUPPLY SOURCE. UNDERCOAT SEAL FOR HARSH
WEATHER.
HINT: Step boards: For Longevity, check rubber seals before installation. Rubber grommets around red and blue wires going into rear
sockets, should be inserted and recessed about 1/4". NOTE: Remove bulbs and apply white grease into sockets and replace bulbs.
Apply RTV Silicone where lights go into socket. Install lights and run wire loom as shown. See Figure 5. For Aluminum Running
board, run wire loom down center as shown. See Figure 4.
STEP 6. Lighting attachment:
INSTRUCTIONS-INSTRUCCIONES-CONSIGNES
APPLICATION:
APPLICACION:
APPLICATION:
1
CONTENIDO - CONTENU
Locate a pass-through point (usually under carpet at drivers feet) for the wire harness. See Figure 8.
2005 TOYOTA TACOMA X-CAB, D-CAB
TOYOTA TACOMA X-CAB, D-CAB, MOD. 2005
2005 TOYOTA TACOMA X-CAB, D-CAB
TOOLS-HERRAMIENTA-OUTILS
7/16" SOCKET
7/16" WRENCH
13MM SOCKET
13MM WRENCH
RATCHET
TORQUE WRENCH
DADO DE 7/16"
LLAVE DE TUERCAS DE 7/16"
DADO DE 13MM
LLAVE DE TUERCAS DE 13MM
MANERAL
LLAVE DE TORQUE
DOUILLE 7/16 PO
CLEF 7/16 PO
DOUILLE 13MM
CLEF 13MM
CLIQUET
CLÉ DE COUPLE
WO:
2 4
3
NOTE: For lighted
NOTE: For lighted version of
75-0713 REVISION 5/24/06
5