Beamz BBP94W Mode D'emploi page 7

To adjust sound sensitivity for in Sound-Active mode
1. Press <SENSITIVITY> on the remote controller.
2. Press <+> or <–> to either increase or decrease sound sensitivity.
To enable DMX or disallow DMX on the product.
Press <DMX> on the remote controller, the product work on the DMX controlling modes.
1. Press <MANUAL> on the remote controller.
2. Press <R>, <G>, <B>, <W>, <A> or <UV> (red, green, blue, white, amber or uv) to choose your colour.
3. Press again <R>, <G>, <B>, <W>, < A> or <UV> (red, green, blue, white, amber or uv) to close your colour.
4. Press <+> or <–> to either increase or decrease the percentage of each colour.
To adjust the FADE speed of the automatic program, the sound active program and the manual mode.
1. Press <FADE> on the remote controller.
2. Press <FADE> again to turn off the Fade mode.
To adjust the brightness value of the automatic program, the Sound active program and Manual Mode.
Press digit <1> to <9> to change different brightness on the device.
The remote control is supplied with a battery inserted. An insulating foil between the battery and the battery contacts prevents the battery
from being discharged during storage. Prior to the first operation remove the foil from the battery support on the rear side of the remote
control. Otherwise operation of the remote control is not possible.
If the range of the remote control decreases, replace the battery. For this purpose, on the rear side of the remote control
press the small bar with the groove to the right (1) and at the same time remove the battery support (2). For operation, one
3 V button cell type CR 2025 is required. When inserting, pay attention that the positive pole of
The unit can be used with wireless DMX. The wireless receiver module, functions only as a receiver of a 2.4 GHz wireless signal. Switch DMX on wirelessly
via the main menu (see menu structure, behind of the manual for more information).
Then establish a wireless connection with the Beamz BPP Wireless DMX Transmitter (154.077).
The BPP Wireless DMX Transmitter and unit must be connected on the same DMX Universe, you can check easily by the colour of
LED indicator.
The buildup of dust, dirt and other airborne particles will reduce the unit's light output. It will also prevent the unit from cooling correctly, and this will
reduce the unit's lifetime. The rate of dirt buildup will vary depending on environmental factors such as airborne dust, use of smoke machines, airflow
from ventilation systems, etc. The unit's cooling fans will accelerate buildup, and any smoke particles that are present in the atmosphere will increase the
tendency for dirt to clog.
To get the best performance and lifetime from the unit, inspect it regularly and clean it as soon as you see signs of dirt buildup.
Assess the operating environment each time you begin to use the unit. In dusty or smoky conditions, inspect the unit after a few hours and check it
frequently the unit may attract dirt faster than you expect. Draw up a cleaning schedule that will make sure that dirt is removed before it can build up.
Use the following guidelines:
• Disconnect the unit from power and allow it to cool completely before cleaning.
• Do not use solvents, abrasives or any other aggressive product to clean the unit.
• Vacuum or use low-pressure compressed air to remove dust and loose particles from surfaces and air vents. Prevent the blades of cooling fans
from turning before you aim a vacuum or air jet at the fan, or you may spin the fan too fast and damage it.
• Clean glass components by wiping gently with a soft, clean, lint-free cloth moistened with a weak detergent solution. Put the solution on the cloth
and not on the surface to be cleaned. Avoid rubbing glass surfaces.
• Dry the unit with a soft, clean, lint-free cloth or low-pressure compressed air before reapplying power.
Red 1 ~ 512
Green 1 ~ 512
Yellow 1 ~ 512
Blue 1 ~ 512
Magenta 1 ~ 512
Cyan 1 ~ 512
White 1 ~ 512