Publicité
Les langues disponibles
Les langues disponibles
OWNER'S MANUAL | USING YOUR BLACKSTONE
IGNITIoN INSTRUCTIoNS
1. CHECK VALVES
ensure gas is off at the supply shut off valve before checking
appliance valves�
Turn all knobs to the ❶ ❶ oFF position�
STEP 01
Push in knob and release� Knob should spring back�
STEP 02
If knobs do NoT
If knobs
do NoT spring back, replace valve assembly before using appliance.
spring back, replace valve assembly before using appliance.
Rotate knob to loW then turn back to oFF� Knob should
STEP 03
turn smoothly�
3. ALWAYS CHECK BURNER FLAME BEFORE USE.
light burners and rotate knobs from HIGH to loW�
STEP 01
look below the cooking surface to view burners� When knob
STEP 02
is at HIGH, flames should be larger than when knob is at loW�
HEALTHY FLAME PATTERN
❶ ❶
❷ ❷
❸ ❸
❶ ❶
Flickers of yellow color.
Flickers of yellow color.
❷ ❷
dark blue color.
dark blue color.
❸ ❸
Vibrant blue.
Vibrant blue.
14
3. ALWAYS CHECK BURNER FLAME BEFORE USE.
YELLOW OR IRREGULAR
If there is a sudden drop or low
If there is a sudden drop or low
flame issue, please reference the
flame issue, please reference the
Troubleshooting chapter.
Troubleshooting chapter.
2. BATTERY POWERED ELECTRIC IGNITION
2. BATTERY POWERED IGNITION
Insert one (1) AA
STEP 01
Insert one (1) AA
STEP 01
battery (not included) under the
battery (not included) under the
ignitor button�
battery cap�
Screw the button into place over
Screw the cap into place over the
the positive terminal�
positive terminal�
Turn gas oN by turning
Turn gas oN by turning
STEP 02
STEP 02
the gas cylinder handwheel
the gas cylinder handwheel
counterclockwise 1 to 3 turns�
counterclockwise 1 to 3 turns�
STEP 03
❷ ❷ Push and hold the ignitor button�
STEP 03
❸ ❸ Push and turn the control knob counter-clockwise to HIGH�
❶ ❶ Push the control knob in to
(Release the ignitor button when the burner lights�)
start gas flowing�
❹ ❹ Adjust the temperature to desired level�
❷ ❷ Turn the control knob
counter-clockwise to activate
❶ ❶
the starter�
❸ ❸ Check flame and adjust the
temperature to desired level�
❸ ❸
❹ ❹
If burner does not ignite with open gas supply valve, gas
will continue to flow out of burner and could accidentally/
inadvertently ignite with risk of injury.
If ignition does not occur in 5 seconds:
1. Turn the burner control knob OFF.
2. Wait 5 minutes.
3. Repeat the lighting procedure.
If burner does not ignite, please reference the Troubleshooting chapter.
If burner does not ignite, please reference the Troubleshooting chapter.
Model: 6009
Clean the battery and appliance
Clean the battery and appliance
Clean the battery and appliance
Clean the battery and appliance
contacts prior to battery installation.
contacts prior to battery installation.
contacts prior to battery installation.
contacts prior to battery installation.
1 to 3 turns
1 to 3 turns
1 to 3 turns
1 to 3 turns
❶ ❶
❷ ❷
❷ ❷
❸ ❸
WARNING
BLACKSTONEPRODUCTS.COM/SUPPORT
WARNING
2. EL
do
Make s
STEP 0
(optio
until it
puddle
STEP 0
❶ ❶ Pu
start g
❷ ❷ Tur
counte
starter
❸ ❸ Ch
the tem
level� (
Note: If
will be o
Publicité
