Publicité
Les langues disponibles
Les langues disponibles
The Controls
! Warning, after pressing the START/PAUSE button
the programme cannot be changed. To change a selected
programme, press the START/PAUSE button
flashes Amber to indicate the programme is paused. Select
the new programme and any options required, the light will
then flash green. Press the START/PAUSE button
and the new programme will start.
• Option buttons
These buttons serves to personalise the selected
programme according to personal requirements.
Not all options are available for all programmes.
Some options are incompatible with the ones
previously set. If the button of any unavailable option
is pressed, the buzzer will beep 3 times. If the option
is available, the option light will stay on.
Progress (
Drying,
Cool Tumble) icons
These are part of the Display, they indicate the progress of
the dryer. Each icon comes on as the corresponding phase
starts.
Delay Timer (Time Delay)
The start of some programmes (see The Display and
Programmes tables) can be delayed for up to 24 hours.
Ensure the water container is emptied before setting a
delayed start.
Ready to Iron
This option allows you to dry loads where only some of the
items need ironing and you do not wish to fully dry those
items. When Iron Dry level is reached, a buzzer sounds
to let you know that the items that need ironing can be
removed. The dryer then stops and the START/PAUSE
light flashes orange. Remove the items you wish to iron,
close the door and press the START/PAUSE button
dryer continues until the remaining items reach the selected
dryness level. It can be used for load sizes up to 3kg.
Less Tangled
This option has the drum movement modified to give a
tumbling action that reduces tangling and knotting of your
clothes. The Less Tangled option gives best results when
used with smaller loads.
Heat Level button and lights
Not all programmes allow you to change the heat level and
some programmes allow all three heat level options:
Low, Medium and High.
When the heat level options are available pressing this
button changes the heat level and the light corresponding to
the selection is lit.
•
DISPLAY "8:88"
The display shows either the amount of time delay remaining
or an indication of the amount of time left for a drying
programme (see The Display). The colons between the
hours and minutes in the display flash to show that the time
is counting down. When the programme finishes its cool
tumble phase the display will show 'End'.
,
•
Empty Water Icon / Container
the light
(If you have plumbed your dryer to a drain this icon can be
ignored, as there is no need to empty the water container).
When this icon is on (
again
container.
If the water container fills during a programme, the heater turns
off and the dryer does a period of Cool Tumble then the buzzer
sounds, the 'water container full' icon
shows "H20" and the 'empty water' icon
You must empty the water container and restart the dryer or
the clothes will not dry. After re-starting the dryer the display will
take a few seconds to refresh. To avoid this always empty the
water container each time you use the dryer (see Maintenance).
•
Door Opening
Opening the door (or pressing the Start/Pause Button) during a
programme will stop the dryer and have the following effects:
• The START/PAUSE light flashes Amber.
• During a delay phase the delay will continue to count
down. The START/PAUSE button must be pressed to
resume the delay programme.
• The START/PAUSE button must be pressed to resume
the programme. The progress lights will change to show
the current status and the Start/Pause light will stop
flashing and turn green.
• Changing the Programmes knob will select a new
programme and the START/PAUSE Light will flash
green. You can use this to select the "Refresh"
programme to cool the clothes if you find them dry
enough. Pressing the START/PAUSE button to begin
new Programme.
•
Note
, the
If you have a power cut, switch off the power or remove the
plug. When power is restored, plug in the machine, press and
hold the ON/OFF button until the dryer reactivates, then press
Start/Pause button.
) it reminds you to empty the water
flashes, the display
is on.
GB
13
Publicité
