stayer MULTI TOOL 300 Instructions D'emploi page 14

Piros színű csiszolóanyag
Material Application
- All wooden For coarse-
materials (e.g., sanding, e.g. of
hardwood, rough, unplaned
softwood, beams and
chipboard, boards
building board) .
For face
sanding and
- Metal materials
planing small
irregularities
For finish and
fine sanding of
wood
Dust/Chip Extraction
Dusts from materials such as lead-containing coatings,
some wood types, minerals and metal can be harmful to
one's health. Touching or breathing-in the dusts can cause
allergic reactions and/or lead to respiratory infections of
the user or bystanders.
Certain dusts, such as oak or beech dust, are considered
as carcinogenic, especially in connection with wood-
treatment additives (chromate, wood preservative).
Materials containing asbestos may only be worked by
specialists.
– As far as possible, use a dust extraction system suitable
for the material.
– Provide for good ventilation of the working place.
– It is recommended to wear a P2 filterclass respirator.
Observe the relevant regulations in your country for the
materials to be worked.
Connecting the Dust Extraction (see figure A)
For sanding, always connect dust extraction. Remove
the application tool/accessory when mounting the dust
extraction 11 (accessory).
If required, assemble the parts of the dust extraction
11 as shown in the figure. Position the assembled dust
extraction onto the machine via the tool holder 4.
Depending on machine version, place a vacuum hose
(accessory) either directly onto the vacuum connection
12. Connect the vacuum hose with a vacuum cleaner
(accessory). An overview for the connection of various
vacuum cleaners can be found on the fold-out page.
The vacuum cleaner must be suitable for the material
being worked.
When vacuuming dry dust that is especially detrimental
to health or carcinogenic, use a special vacuum cleaner.
ENGLISH
14
4. Operation
Observe correct mains voltage! The voltage of the
power source must agree with the voltage specified
on the nameplate of the machine. Power tools marked
with 230 V can also be operated with 220 V.
Grain size
Starting Operation Switching On and Off
Coarse 60
To start the machine, push the On/Off switch 1 forward so
that the "I" is indicated on the switch.
To switch off the machine, push the On/Off switch 1 toward
Medium 80
the rear so that the "0" is indicated on the switch.
Preselecting the Orbital Stroke Rate
Fine 210
Note: Do not cover off the venting slots 3 of the machine
while working, as this reduces the working life of the
machine.
Operating Principle
Sawing
- Use undamaged faultless saw blades only. Deformed,
- When sawing light building materials, observe the
- Plunge cuts may only be applied to soft materials,
Before sawing with HSS saw blades in wood, particle
board, building materials, etc., check these for foreign
objects such as nails, screws, or similar. If required,
remove foreign objects or use BIM saw blades.
Sanding
The removal rate and the sanding pattern are primarily
determined by the choice of sanding sheet, the preset
oscillation rate and the applied pressure.
Only flawless sanding sheets achieve good sanding
capacity and extend the service life of the machine.
Pay attention to apply uniform sanding pressure; this
increases the working life of the sanding sheets.
14
Due to the oscillating drive the application
tool/accessory swings up to 21000 times
per minute for 2.8°. This allows for precise
work in narrow spaces.
Work with low and uniform application
pressure,
performance will decline and the application
tool can become blocked.
While working, move the machine back and
forth, so that the application tool does not
heat up excessively and become blocked.
blunt saw blades or saw blades that are otherwise
damaged can break.
statutory provisions and the recommendations of
the material suppliers.
such as wood, gypsum plaster boards, etc.!
otherwise, the working