Fortin INT-SL Guide Rapide

1
Make the connections of the INT-SL to the
vehicle:
1.A Connector 1 (Black):
Determine the type of installation:
INSTALLATION WITH DATA-LINK
INSTALLATION WITHOUT DATA-LINK
Connector 2 (White):
1.B
Make the connections
Press and hold the programming
2
button. Plug in the
in the INT-SL interface.
The LED will turn on, indicating
3
the beginning of programming.
Plug the
INT-SL interface.
4
WARNING: Connector 2 can be easily
plugged in backwards.
While holding the programming
5
button, turn the key to the ignition
position.
6
The LED will flash rapidly.
7
Release the programming button.
8
Start the vehicle with the key.
9
The LED will turn off.
10
Turn the key OFF.
The interface is programmed.
PONTIAC Bonneville
FONCTIONNAL IF EQUIPPED
R
Bypass PK3, Passlock or VATS
R
Doorlock Control
R
Factory Alarm Control (OEM)
R
Trunk Release
£
Door status
WITH DATA-LINK
connector 1
connector 2 into the
WITHOUT DATA-LINK
Connect wire to Remote-Starter/Alarm
Copyright © 2009, FORTIN AUTO RADIO INC
2000-2005
DATA INTERFACE MODULE FOR SECURITY SYSTEM / REMOTE STARTER.
R
Heated Seats and Heated
Mirrors (Heated seats will turn
ON (low power) ONLY if the
engine temp is below 0°C
(32°F) when remote started.)
R
Rear Defrost
WARNING: Connector 2 can be easily plugged in backwards.
N.C. Lt. Blue
White
N.C.
Ignition Pink
Blue
N.C.
Orange
Door trigger
Data OBD2 2 Purple
PIN 2
Bypass Pk3 Yellow Yellow
2
1 2 4 8
3 5 6 7
9 11 12 13 15
10 14 16
Pink
Yellow
or white
Black
1
WARNING: Connector 2 can be easily plugged in backwards.
Lock
Unlock Driver 1
Ignition
(-) While running
Door trigger
Data OBD2
2
Bypass Pk3
PIN 2
2
1 2 3 4 5 6 7 8
9 10 11 12 13 14 15 16
1
Cut off one plug of the Data-Link connector,
connect the red wire to +12V and the black wire
to ground.
Connect wire to vehicle
Technical support:
TEL: 514-255-HELP (4357)
FAX: 514-255-1367
Web: www.ifar.ca
ALL RIGHTS RESERVED
INT-SL
WEB
UPDATE Made in Canada - Rev.
W e b s i t e : h t t p : / / w w w . i f a r . c a
R R
Parking Light Control
R
Retained Accessory Power
R
Memory selection Driver 1 and
2 (by Unlock)
£
Start
£
Slidding doors
In Data-Link mode the analog
Lt. Blue/Black
Input (unlock, ground out) are
N.C.
White/Black
N.C.
Pink/Black
N.C.
Green N.C.
Tach
Orange/Black
~
Purple/White or Purple/Black
N.C.
Yellow/Black
Bypass Pk3
B y p a s s P K 3 :
Connection needed
ONLY if the Security light
stays ON with the key in
ON position (ignition).
FOR OLD CADILLAC
MODELS ONLY
Lt. Blue/Black
Lt. Blue
White White/Black
Unlock Driver 2
Pink Pink/Black Parking Light
Blue Green
N.C.
Orange Orange/Black
~
Purple
Purple/White or Purple/Black
Yellow/Black Bypass Pk3
Yellow Yellow
B y p a s s
Connection needed
Pink
ONLY if the Security light
Yellow
stays ON with the key in
or white
ON position (ignition).
Black
FOR OLD CADILLAC
MODELS ONLY
Red +12V
Black
Neither the manufacturer or distributor of this module is
responsible of damages of any kind indirectly or directly
caused by this module, except for the replacement of this
module in case of manufacturing defects. This module must
be install by qualified technician. This instruction guide may
change without notice. Visit www.ifar.ca to get latest version.
C - 07 / 04 / 200
Tach
disabled for security.
Starter or alarm
Data Link Port
Trunk
Tach
N.C.
P K 3 :
OUTPUT INPUT