Fortin INT-SL Guide Rapide

Fonctionnal if equipped
R Lock R Tach
R £
Unlock Start Enable
R Arm R Door Trigger
R Disarm R Trunk Trigger
R £
Trunk Hood Trigger
Trunk Trigger
Tach
Ground Out
Lock
Key Sense
conn.
1
Connector 1 (Black - 4 pins):
LED
Determin the type of installation:
INSTALLATION
Front of the module
DATA-LINK
INSTALLATION
WITHOUT
DATA-LINK
Cut off one plug of the Data-Link connector, connect the red wire to +12V and the black wire to ground.
4
Web Update
connector*
* Connector not supplied
3
1 Brown/White
Grey
conn.
Grey/Black
Brown
4
Back of the module
Connect wire to Remote-Starter/Alarm
Copyright © 2008, FORTIN AUTO RADIO INC ALL RIGHTS RESERVED
VOLVO XC90
£ Radio Off £ Heat Seats
£ Transponder Bypass £
Gas Door
£ PK3, Passlock £ Window Roll Down
£ Slidding Door £ Hatch
£ £
Defrost Brake Signal
8 1
Lt. Blue Lt. Blue/Black
N.C.
White White/Black
~
Pink Pink/Black
~
Blue Green
2
Orange Orange/Black
N.C.
Purple
Purple/Black or Purple/White
Yellow Yellow/Black
14
7
Rede
conn.
Data-Link connector
Black
WITH
Blue
White
Red
+12V
Black Ground
Blue
White
Connector 4 (White -
4 pins):
Connect with the
FLASH LINK
UPDATER for web
update.
N.C.
(CAN High) Data
(CAN Low) Data
N.C.
Connect wire to vehicle
Technical support:
TEL: 514-255-HELP (4357)
FAX: 514-255-1367
Web: www.ifar.ca
2005-2009
N.C.
N.C.
N.C.
Door Trigger
N.C.
Unlock
Trunk
1
1
Starter or alarm
Port Data Link
White
3
11
Green
OUTPUT INPUT
Neither the manufacturer or distributor of this module is
responsible of damages of any kind indirectly or directly
caused by this module, except for the replacement of this
module in case of manufacturing defects. This module must
be install by qualified technician. This instruction guide may
change without notice. Visit www.ifar.ca to get latest version.
CAN-SL2
WEB
Made in Canada - Rev. B - 09 / 02 / 2009
UPDATE
W e b s i t e
ALARM AND REMOTE STARTER CAN BUS INTERFACE KIT
Data-Link (1 way)
Connect: Connect:
8 1
Lt. Blue Lt. Blue
Lt. Blue/Black
White White
White/Black
Pink
Pink/Black
1
Blue Green Brown/White
Grey
Orange Orange/Black Orange
Grey/Black
Purple Purple/Black Purple
Brown
Yellow Yellow/Black Yellow
4
14
7
Make the connections of the CAN-SL2 to the
vehicle:
1
1.A
Connector 1 (Black):
Determine the type of installation:
INSTALLATION WITH DATA-LINK
INSTALLATION WITHOUT DATA-LINK
1.B
Connector 2 (White):
Make the connections
1.C
Connector 3 (White, located at the back of the module):
Make the connections
Press the programming switch while
inserting the main wires harness (CONN 1)
into the CAN-SL2 module.
The LED will illuminate to indicate you are
2
in programming mode, release the
programming button.
Connect the other connectors
(CONN. 2)
3
WARNING: Connector 2 can be easily
plugged in backwards.
Connect the other connectors
4
(CONN. 3)
5
Turn the key to the "ON" position.
Once the LED starts to flash rapidly
the key to the OFF position.
6
The LED will turn off to indicate the
module has been programmed.
The module is now ready for use.
: h t t p : / / w w w . i f a r . c a
Data-Link (2 way)
8 1
Lt. Blue/Black
White/Black
Pink
Pink/Black
1
Blue Green Brown/White
Grey
Orange/Black
Grey/Black
Purple/Black
Brown
Yellow/Black
4
14
7
turn