monzana MZPP15T Mode D'emploi page 7

12
Problembehebung
Achtung: erst die Pumpe vom Strom trennen, bevor irgendwelche Maßnahmen
ergriffen werden!
Problem Ursache
Pumpe ohne Aktion Kein Strom vorhanden
Pumpe arbeitet hörbar, aber es 1.Luft im System (Pumpe/Tank)
fließt kein Wasser
2.Schläuche verknickt Pumpe
zieht Luft
3.Ansaughöhe zu hoch Falscher
Ansaugschlauch
Geringe Durchflussmenge 1.Ansaug-/
Förderhöheüberschritten
2.Ventil/Schlauch/
Filterverunreinigt
Plötzlicher Stopp der Pumpe Überhitzung hat den
Thermoschalter ausgelöst
Sand im Poolwasser Frischer Sand im Filter
Weiterhin Sand im Wasser Falschen Quarzsand genutzt
Erhöhter Druck 1.Verstopfung
2.Hohe Verschmutzung
Lösung
Stecker einstecken bzw. ggf.
Sicherungen prüfen
1.Entlüften Sie die Pumpe wie
beschrieben und ggf auch den
Tank.
2.Prüfen und ggf begradigen
Verbindungen prüfen und
abdichten. Evtl Schlauch
undicht
3.Position der Pumpe
anpassen Unterdrucksicheren
Ansaugschlauch nutzen
1.Position der Pumpe/des
Systems anpassen
2.Prüfen und ggf. reinigen
Unterdrucksicheren
Ansaugschlauch nutzen
-ca. 30 Minuten abwarten
-Unterdrucksicheren
Ansaugschlauch nutzen
-Verstopfte Leitungen prüfen
Bei der Nutzung von frischem
Sand ist das normal. Gehen Sie
vor wie beschrieben. Es legt
sich dann von alleine.
Sand zu fein, besorgen Sie
gröberen Sand im Fachhandel
1.Reinigen
2.Reinigen & Rückspülen
INSTRUCTIONS
ATTENTION! Read the safety and assembly instructions carefully, in order to
avoid the risk of injury or damaging the product.
Important: Read these instructions carefully and thoroughly. Keep these
instructions to read through at a later date. If you give the product to
anyone else at some point in the future, please ensure you also pass on this
manual
Only for domestic use and not for
commercial use!
Keep small parts, plastic bags and other packaging out of the reach of children.
Pay attention especially when unpacking your item. Danger of suffocation!
Check the delivery for completeness. Later complaints cannot be accepted.
Check all elements and parts for damages. Despite careful control, products may be
damaged in transit. In this case, do not assemble your product. Defective parts can en-
danger your health.
Never modify the product! Changes will void the warranty and the product may be
unsafe or even dangerous.
Unpack all the parts and elements of the set and place the components on the top of
the carton or other clean surface. This protects your new product.
Please also pay attention not to scratch the floor while working with tools.
Make sure that this product is fully assembled before use, as shown in the illustration
For cleaning use a sponge and warm soapy water.
Do not use solvent based-cleaners or detergents - for example bleach. Those can dam-
age the product.
Intended Use
The sand filter system is used in combination with a pump suitable for cleaning pool water
(suitable for dug-in and non dug-in pools). The system does not require maintenance.
However, it is important that the sand is cleaned at regular intervals using the backwash
function. A sand filter system is not intended to remove or neutralise algae, bacteria and
other pathogens/ germs, etc. Healthy pool water can only be achieved when combined
with the right pool chemicals and water care products. This system removes suspended
solids and similar substances in the water. A floor extraction system is also important, as
the system can only filter suspended substances. Use the product only for the purpose
for which it is intended. The manufacturer accepts no liability for damage caused by
improper use. Any modification to the product may negatively impact safety, cause
hazards and void the warranty.
13