EINHELL TE-RS 18 Li Instructions D'origine page 17

All manuals and user guides at all-guides.com
batteries and without a charger and is allowed to
be used only with the lithium-ion batteries of the
Power-X-Change series!
The lithium-ion batteries of the Power-X-Change
series are allowed to be charged only with Power-
X chargers.
Danger!
Sound and vibration
Sound and vibration values were measured in
accordance with EN 62841.
L sound pressure level ..................... 74.3 dB(A)
pA
K uncertainty ............................................. 3 dB
pA
L sound power level ....................... 85.3 dB(A)
WA
K uncertainty ............................................. 3 dB
WA
Wear ear-muff s.
The impact of noise can cause damage to hea-
ring.
Total vibration values (vector sum of three direc-
tions) determined in accordance with EN 62841.
Vibration emission value a
K uncertainty = 1.5 m/s
2
The stated vibration emission levels and stated
noise emission values were measured in ac-
cordance with a set of standardized criteria and
can be used to compare one power tool with
another.
The stated vibration emission levels and stated
noise emission values can also be used to make
an initial assessment of exposure.
Warning:
The vibration and noise emission levels may vary
from the level specifi ed during actual use, depen-
ding on the way in which the power tool is used,
especially the type of workpiece it is used for.
Keep the noise emissions and vibrations to a
minimum.
•
Only use appliances which are in perfect wor-
king order.
•
Service and clean the appliance regularly.
•
Adapt your working style to suit the appliance.
•
Do not overload the appliance.
•
Have the appliance serviced whenever ne-
cessary.
Anl_TE_RS_18_Li_SPK9.indb 17 Anl_TE_RS_18_Li_SPK9.indb 17
GB
•
•
Limit the operating time!
All stages of the operating cycle must be conside-
red (for example, times in which the electric tools
are switched off and times in which the tool is
switched on but operates without load).
Caution!
Residual risks
Even if you use this electric power tool in
accordance with instructions, certain resi-
dual risks cannot be rules out. The following
hazards may arise in connection with the
equipment's construction and layout:
1. Lung damage if no suitable protective dust
2. Damage to hearing if no suitable ear protec-
3. Health damage caused by hand-arm vib-
= 5.33 m/s 5. Before using the equipment
2
h
Warning!
Always remove the battery pack before making
adjustments to the equipment.
Be sure to read the following information before
you put the cordless equipment into operation:
•
5.1 Installing the dust extractor adapter (Fig.
Plug the dust extractor adapter (2) onto the va-
cuum cleaner connector (a) as shown in Fig. 2.
Connect the dust extractor adapter to a suitable
dust extraction system.
5.2 Fitting the dust bag (Fig. 3/Item 4)
•
•
•
- 17 -
Switch the appliance off when it is not in use.
Wear protective gloves.
mask is used.
tion is used.
rations if the equipment is used over a pro-
longed period or is not properly guided and
maintained.
Charge the battery pack with the charger. An
empty battery pack requires a charging peri-
od of approximately 0.5 to 1 hour.
2/Item 2)
Fit the dust bag (4) on the dust extractor
adapter (2) by twisting it gently as far as the
notch (b) as shown in Fig. 3.
The dust is extracted directly into the dust
bag (4) through the abrasive paper and the
oscillating plate (5).
Twist and pull the dust bag simultaneously to
remove it again.
27.09.2019 13:09:37 27.09.2019 13:09:37