Hoover BR71 Manuel D'utilisation page 5

5. Remove the Vortex Finder from bin assembly. [11]
6. Empty the dust from the bin. [12]
7. Refit the vortex finder and pre-motor filter assembly to bin assembly.
8. Refit the dust container lid to bin assembly.
9. Close and refit to the cleaner main body.
Cleaning the washable Filters
The cleaner is fitted with pre motor filter and exhaust filter. To maintain optimum cleaning
performance, regularly remove the filters and tap against the side of the bin to release dust. The
filters should be washed every 5 cassette empties or when the filter has excessive dust level.
ImPORTANT: All bagless cleaners require regular filter cleaning. Failure to clean your
filters may result in air blockage, overheating and product failure. This may invalidate
your guarantee.
ImPORTANT: Regularly check and maintain the filters.
ImPORTANT: Always ensure the filter pack is fully dry before use.
To access the filter:
1. Remove the dust container from the cleaner. [8]
2. Hold the dust container with one hand, and remove the dust container lid by rotating
anti-clockwise. [9]
3. Remove the pre-motor filter assembly from bin assembly. [10]
4. Gently tap and wash the pre-motor filter. Do not use hot water or detergents. Remove
excess water from the filter and leave to dry fully before re-using. [13] [17]
5. Reassemble the pre-motor filter assembly once fully dry and refit to the cleaner.
To access the exhaust filter:
1. Unclip the exhaust filter cover from the rear of the cleaner main body. [14]
2. Remove the exhaust filter from the rear of the cleaner. [15]
3. Gently tap and wash the filter using warm water. Do not use hot water or detergents.
Remove excess water from the filter and leave to dry fully before re-using. [16] [17]
4. Refit the exhaust filter to the rear of the cleaner once fully dry and refit the exhaust filter cover.
ImPORTANT: Do not use the product without the filter pack fitted.
Cleaning the dust container / separation unit
This cleaner uses a separation system unique to Hoover. If necessary the separation unit can be
disassembled from the dust container and cleaned.
1. Press the dust container release button and remove the bin assembly from the cleaner. [8]
2. Hold the bin with one hand and with the other hand remove the dust container lid by
rotating anti-clockwise. [9]
3. Remove the dust container lid by rotating anti-clockwise. And remove the pre-motor filter
from dust container assembly. [10] And then remove the vortex finder from the dust
container by pulling. [11]
4. If necessary, use a cloth to remove excessive dust from the vortex finder surface. Reassemble
the internal components to the bin.
5. Reassemble the dust container lid to the dust container. Refit the dustbin to the cleaner.
Removing a blockage
1. Check if the Dust Container is full. If so, refer to 'Emptying The Dust Container' .
2. If the Dust Container is empty, but suction is still low:
*Certain Models Only ** Certain models only, nozzles may vary according to model
A. Do the filters need cleaning? If so, refer to 'Cleaning the Washable Filters' .
B. Check if there is any other blockage in the system - Use a rod or a pole to remove any
blockage from the tubes or hose.
C. Check for and clear any blockage in the Nozzle
D. Check if the separation unit needs to be cleaned. Refer to 'Cleaning the separation unit.
wARNING - If the cleaner is used for a significant period of time with a blockage, a thermal cut
out will switch the cleaner off to prevent overheating. If this should happen, switch the cleaner off,
unplug and correct the fault. It will take about 45 minutes for the cut out to automatically reset.
USER CHECklIST
should you have a problem with the product, complete this simple user checklist before calling
your local Hoover service.
• Is there a working electricity supply to the cleaner? Please check with another electrical
appliance.
• Is the dust container over-filled? Please refer to 'Cleaner Maintenance' .
• Is the filter blocked? Please refer to 'Cleaner Maintenance' .
• Is the hose or nozzle blocked? Please refer to 'Removing a blockage from the system' .
• Has the cleaner overheated? If so, it will take approximately 30 minutes to automatically
reset.
ImPORTANT INFORmATION
Hoover Spares and Consumables
Always replace parts with genuine Hoover spares. These are available from your local Hoover
dealer or direct from Hoover. When ordering parts always quote your model number.
Quality
Hoover's factories have been independently assessed for quality. Our products are made using
a quality system which meets the requirements of IsO 9001.
your Guarantee
The guarantee conditions for this appliance are as defined by our representative in the country
in which it is sold. Details regarding these conditions can be obtained from the dealer from
whom the appliance was purchased. The bill of sale or receipt must be produced when making
any claim under the terms of this guarantee.
subject to change without notice.
3
GB