Hoover BR71 Manuel D'utilisation page 4

GETTING TO kNOw yOUR ClEANER
A. suction Regulator
B. Hose Handle
C. Telescopic Tube
D. On/Off Pedal
E. Exhaust filter cover
F. Carpet & Floor nozzle (GP)**
F1. Carpet Nozzle (CA)**
F2. Hard Floor Nozzle (HF)**
G. Floor type selector pedal
H. Park slot
I. Cord reel Pedal
J. Cleaner Main Body
ASSEmBlING yOUR ClEANER
Remove all components from the packaging.
Connect the hose to the cleaner main body, ensuring it clips and locks into position. [1]
1.
To release: simply press the button on the hose end and pull.
2.
Connect the hose handle to the upper extension tube end [2], or accessories if required.
3.
Connect the extension tube lower end to the carpet and floor nozzle [3] or accessories
4.
if required.
USING yOUR ClEANER
Extract power cord and plug it into the power supply. Do not pull the cord beyond the red
1.
marker. [4]
Adjust the telescopic tube to the desired height by moving the telescopic tube adjuster up
2.
and raise or lower the handle to the most comfortable cleaning position. [5]
Carpet & Floor Nozzle**. Press the floor type selector on the nozzle [6] to select the ideal
3.
cleaning mode for the floor type.
Hard Floor – Brushes are lowered to protect the floor.
Carpet – Brushes are raised for the deepest clean.
switch the cleaner on by pressing the on/off Pedal on the cleaner main body. [7]
4.
Adjust the suction regulator on the handle to the desired level.
5.
switch off at the end of use by pressing the on/off Pedal. Unplug and press the cord reel
6.
pedal to wind the power cord back into the cleaner.
PARkING AND STORAGE SECTION
The tube and nozzle can be parked on back of the cleaner for storage or temporary storage
while in use.
*Certain Models Only ** Certain models only, nozzles may vary according to model
K. Hose
L. Dust Container lid
M. Dust Container
N. Vortex Finder
O. Pre-motor Filter
P. Dust Container Release Button
Q. Exhaust Filter
R. 2 in 1 accessory
s. Pet Hair Remover Mini Turbo Nozzle*
T. Allergen Remover Mini Turbo Nozzle*
U. Grand Turbo nozzle*
V. Parquet Nozzle*
ACCESSORIES
To obtain the best performance and energy efficiency #1 it is recommended that the correct
nozzles are used for the main cleaning operations. These nozzles are indicated in the diagrams
by the letters GP, HF or CA.
A nozzle type GP can be used to clean both carpet and hard floor.
A nozzle type HF is suitable for use only on hard floor.
A nozzle of type CA is suitable for use only on carpet.
The other nozzles are accessories for specialist cleaning tasks and are recommended for
occasional use only.
It is important to note that this vacuum cleaner is supplied with an Energy Label as required by
European Regulation (EU) 665/2013.
If the label shows a red prohibition circle on the left covering the carpet symbol, then this
indicates that the vacuum cleaner is not suitable use on carpets.
If the label shows a red prohibition circle on the right covering the hard floor symbol, then this
indicates that the vacuum cleaner is not suitable for use on hard floors.
#1
NOTE: Dust pick up ability carpet, dust pick up ability hard floor, and energy efficiency in
accord with Commission Regulations (EU) 665/2013 and (EU) 666/2013.
All accessories can be fitted to the hose handle or the end of the tubes.
2 in 1 Tool combines several functions into one tool:
Crevice Tool – For corners and hard to reach areas.
Dusting Brush – For bookshelves, frames, keyboards and other delicate areas.
Pet Hair Remover mini Turbo Nozzle* - Use the mini turbo nozzle on stairs or for deep
cleaning on textile surfaces and other hard to clean areas. Particularly suitable for pet hairs
removal.
Allergen Remover mini Turbo Nozzle* – Use the mini turbo nozzle on stairs or for deep
cleaning on textile surfaces and other hard to clean areas. Particularly suitable for allergen
removal.
Parquet Nozzle* – For parquet floors and other delicate floors.
ImPORTANT: Do not use the Mini Turbo Nozzles on rugs with long fringes, animal hides and
carpet pile deeper than 15mm. Do not keep the nozzle stationary while the brush is rotating.
ClEANER mAINTENANCE
Emptying the Dust Container
When the dust reaches the max level indicator on the container, empty the dust container.
ImPORTANT: To maintain optimum performance, do not allow the dust to exceed the max level.
1. Turn off the cleaner with the main switch and unplug the power cable.
2. Press the bin release button and remove the bin assembly from the cleaner. [8]
3. Hold the dust container with one hand, and remove the dust container lid by rotating
anti-clockwise. [9]
4. Remove the pre-motor filter assembly from bin assembly. [10]
2
GB