Cleaning And Maintenance - Celexon DELUXX SCREEN ELECTRIC PROFESSIONAL Manuel D'installation

Table des Matières

Les langues disponibles

ENGLISH – Rolling screen installation and operation manual

The screen product is manufactured in compliance with the provisions of the following EC directives: 2014-35-CE LDV Low voltage

The screen described in this manual must be used exclusively as a support for video projection. Any other use not covered by this manual, it is not consented.

The screen contains one or more Fabric/sheet of projection. The Fabric of projection is a cadmium-free plastic pvc sheet or Glass wire (continuos filament) plastified PVC impregnated, any fabric can be

classified in category:

M1 and M2 fire classification under French standards (LNE Laboratoire national de métrologie et d'essais – SME Centre de recherches du Bouchet - WARRINGTONFIRE GENT Laboratoire de

métrologie et d'essais – IFTH Laboratoire accreditè

B1 and B2 fire classification under German standards (LNE Laboratoire national de métrologie et d'essais – SME Centre de recherches du Bouchet - WARRINGTONFIRE GENT Laboratoire

national de métrologie et d'essais)

UL94HB fire classification under USA standards (THE GOVMARK Organization, Inc.)

In the absence of a standardisation at a European level of the various national classification norms, it should be noted that the French M1 class corresponds to non flammable material and that M2 class

corresponds to flame retardant material. The screens use projection fabrics/sheets composed mainly of plasticized PVC or fibreglass. As these fabrics are sensitive to temperature and humidity, the

acceptable size tolerance is 1% in each dimension.

There is a tolerance of +/-2 mm on the aluminium profiles used.

The tollerance on the overall size are:

+/- 3 mm up to an overall size of 2500 mm;

+/- 5 mm up to an overall size of 4000 mm;

+/- 10 mm up to an overall size of 8000 mm;

+/- 20 mm up to an overall size of 16000 mm;

+/- 30 mm up to an overall size of 24000 mm.

Screens and their projection surfaces are delicate and must be cleaned with great care, according to the following instructions:

Never use solvents, chemical or abrasive products, or pointed tools to clean the surface.

Avoid contact with other materials (varnishes, inks etc) as they might be impossible to remove from the canvas.

FABRIC VISION, REFERENCE, HELIOS: Remove dust from the case with a soft, clean cloth and a non aggressive detergent as necessary.

Clean the projection screen with a soft, clean, damp cloth, and a neutral or alcohol-base detergent as necessary. Since rubbing the screen with a cloth during cleaning operations can cause electrostatic

charge to accumulate, we recommend the subsequent application of an antistatic liquid with a clean cloth, to avoid dust being attracted again

GENERIC PROFILE: Remove dust from the case with a soft, clean cloth and a non aggressive detergent as necessary

VELVET PROFILE: Clean profile with a soft clean cloth, or a brush with soft, antistatic bristles. A vacuum-cleaner brush may be used, provided its bristles are soft and perfectly clean.

STRUCTURE and ANCHORING BRACKETS: The state of the product and the anchoring capacity of its brackets must be checked regularly. In case of canvas deformation or rips, or loosening of structural

components such as brackets or screws, action must be taken immediately to clear the area around the screen and avoid hazard to people and things, replace the defective component and restore the

product's functionality.

Ensure that the screen has suffered no damage during transport. Should any fault be detected, promptly notify your dealer. Verify that all screen accessories have been included

Motorised or integrated radio roller screen

-1 Kit with 2 installation brackets (for screens up to 3 m wide)

-1 Kit with 3 installation brackets (for screen over 3 m wide)

-1 10° unipolar, 250V dead man's selector switch with directional arrows, inclusive of wall mount hood

-1 RF transmitter (for integrated radio screen models)

-1 plastic hex wrench

-1 instructions booklet

(screws and plugs for wall mount are not included)

CAUTION do not use cutters or sharp objects to open the wrapping, always use protection gloves when unpacking, handling and installing the product. Depending on the product's weight (reference load: 25

Kg male – 15 Kg female), handling and installing operations should be performed by two, three or four people at least. For heavier loads we recommend the use of specific lifting equipment.

Made by celexon Germany GmbH & Co. KG - Gutenbergstraße 2 - 48282 Emsdetten, Germany / www.deluxx.com

DELUXX® is a brand of celexon Germany GmbH & Co. KG

Specifications are subject to change without prior notice.E&OE

Doc: Classic Winch Professional Installation Manual rev2 | 05.07.2017

Please verify that you are working with the latest revision of this document before specifying your screen.

04 GENERAL CHARACTERISTICS OF THE PRODUCT

2014-30-EU EMC Electromagnetic compatibility

2014-53-CE Radio Equipment

2009-125-CE CONSUMPTION Ecodesign

2011-65-CE ROHS Restriction of Hazardous Substances

2012-19-CE RAEE Waste management

2001-95-CE SAFETY Safe Product