Publicité
Les langues disponibles
Les langues disponibles
B
ÉVACUATION EXTÉRIEURE VERS L'ARRIÈRE (conduit horizontal)
APERÇU DU MONTAGE
B1. Préparez le mur arrière
B2. Enlevez la plaque de ventilation
B3. Fixez la plaque de montage au mur
B4. Préparez l'armoire supérieure
B5. Réglez le ventilateur
B6. Montez le four à micro-ondes
NOTES IMPORTANTES :
- Assurez-vous que les vis du moteur et de la plaque de
ventilation sont bien serrées lorsqu'elles sont
réinstallées. Cela permettra d'éviter des vibrations.
- Assurez-vous que le câblage du moteur
a été correctement acheminé et sécurisé, et que les
câbles ne sont pas coincés.
B1
PRÉPARATION DU MUR ARRIÈRE
POUR L'ÉVACUATION EXTÉRIEURE
VERS L'ARRIÈRE
Vous devez découper une ouverture situé e dans le
mur arriè re pour l'é vacuation vers l'exté rieur.
NOT E:
READ
IT IS VERY
AND FOLL
IMPO RTAN
IN THE
OW THE
T TO
BEFO
INST ALLA
DIRE CTIO
RE PRO
TION INST
NS
REAR
WAL L
CEED
RUC TION
TEM PLAT
ING WITH
S
This Rear
Wall Templa
E.
THIS
3/8" TO EDGE
mounti
ng plate
te serves
outlet.
and to
to positio
12"
1. Use
locate the
horizon
n the bottom
a level
to check
tal exhaus
accura
tely.
that the
t
2. Locate
and mark
templa
te is positio
right side
at least
ned
of the centerl
one stud
on the
4"
screw mounte
I t is importa
ine.
left or
of the microw
d firmly
nt to use
at least
in a stud
one wood
locatio ns
for the
ave. Mark
two additio
to suppor
t the weight
3. Drill
holes in
supplie
nal, evenly
a stud,
the marked
d toggle
bolts.
spaced
that do
drill a 3/16"
locatio ns.
not line
hole for
wood screws
Where
there is
toggle
bolts.
up with
a stud,
. For holes
D O NOT
drill 5/8"
holes for
AT THIS
INSTA LL
4. Remov
TIME.
THE MOUN
5. Review
e the templa
TING PLATE
the Installa
te from
the rear
installa
tion situatio
tion Instruc
wall.
n.
tion book
for your
Darle vuelta
versió n
a la hoja
en Españ
ol.
para consu
ltar la
Loca te
and mark
moun ting
holes to
plate .
align with
IMPO RTAN
holes in
T:
the
LOCA
TE AT
THE CEN
LEAS T
TERL INE.
ONE STUD
MAR K
ON EITH
THE LOCA
ER SIDE
SPAC
TION FOR
OF
ED TOG
2 ADD
AREA
.
GLE BOLT
ITION AL,
S IN THE
EVEN
MOU NTIN
LY
G PLAT
E
Trim the
rear wall
temp late
along
the dotte
d line.
Loca te
and mark
moun ting
plate .
IMPO RTAN
T:
LOCA
TE AT
LEAS T
THE CEN
TERL INE.
MAR K
THE LOCA
SPAC
ED TOG
AREA
GLE BOLT
.
•
Lisez les instructions sur le GABARIT DU
MUR ARRIÈRE.
•
Fixez-le au moyen de ruban adhésif sur le mur
•
Découpez l'ouverture en suivant les instructions du GABARIT DU
MUR ARRIÈRE.
Instructions de montage
Trim the rear wall template
Trim the
rear wall
temp late
along
the dotte
d line.
holes to
align with
holes in
the
ONE STUD
ON EITH
ER SIDE
TION FOR
OF
2 ADD
ITION AL,
S IN THE
MOU NTIN
EVEN
LY
G PLAT
E
3/8" TO EDGE
along the dotted line.
Trim the rear wall template
12"
TO
NOTE: IT IS VERY IMPORTANT
READ AND FOLLOW
THE DIRECTIONS
INSTRUCTION S
IN THE INSTALLATION
WITH THIS
BEFORE PROCEEDING
REAR WALL TEMPLATE.
4"
serves to position the bottom
This Rear Wall Template
the horizontal exhaust
mounting plate and to locate
outlet.
that the template is positioned
1. Use a level to check
accurately.
one stud on the left or
2. Locate and mark at least
right side of the centerline.
least one wood
It is important to use at
screw mounted firmly in
a stud to support the weight
two additional, evenly spaced
of the microwave. Mark
locations for the supplied
toggle bolts.
locations. Where there is
3. Drill holes in the marked
for wood screws. For holes
a stud, drill a 3/16" hole
stud, drill 5/8" holes for
that do not line up with a
toggle bolts.
MOUNTING PLATE
DO NOT INSTALL THE
AT THIS TIME.
from the rear wall.
4. Remove the template
Instruction book for your
5. Review the Installation
installation situation.
para consultar la
Darle vuelta a la hoja
versión en Español.
24"
to align with holes in the
Locate and mark holes
mounting plate.
IMPORTANT:
STUD ON EITHER SIDE
OF
LOCATE AT LEAST ONE
THE CENTERLINE.
FOR 2 ADDITIONAL,
EVENLY
MARK THE LOCATION
IN THE MOUNTING PLATE
SPACED TOGGLE BOLTS
to align with holes in the
AREA.
Locate and mark holes
mounting plate.
IMPORTANT:
STUD ON EITHER SIDE
OF
LOCATE AT LEAST ONE
THE CENTERLINE.
EVENLY
MARK THE LOCATION
FOR 2 ADDITIONAL,
IN THE MOUNTING PLATE
along the dotted line.
SPACED TOGGLE BOLTS
AREA.
REMOVE BLOWER PLATE
B2
RETIREZ LA PLAQUE DE
VENTILATION
Retirez et conservez la vis qui maintient la plaque du
ventilateur au four à micro-ondes. Soulevez la plaque de
ventilation.
Plaque de ventilation
FR-16
Arrière du four
à micro-ondes
Publicité
