stayer BHL 111 B Manuel D'instructions Original page 16

gb
Secure the workpiece. A workpiece clamped with
clamping devices or in a vice is held more secure than
by hand.
Keep your workplace clean. Blends of materials are
particularly dangerous. Dust from light alloys can burn or
explode.
Always wait until the machine has come to a complete
stop before placing it down. The tool insert can jam and
lead to loss of control over the power tool.
Do not open the battery. Danger of shortcircuiting.
Protect the battery against heat, e. g., also against
continuous sun irradiation and fire. There is danger of
explosion.
In case of damage and improper use of the battery,
vapours may be emitted. Provide for fresh air and
seek medical help in case of complaints. The vapours
can irritate the respiratory system.
When the battery is defective, liquid can escape and
come into contact with adjacent components. Check
any parts concerned. Clean such parts or replace them,
if required.
Use the battery only in conjunction with your Stayer
power tool. This measure alone protects the battery
against dangerous overload.
BATTERIES USE AND CARE
Do not open the battery. Danger of shortcircuiting.
Protect the battery against heat, e. g., against continuous
intense sunlight, fire, water, and moisture. Danger of
explosion.
In case of damage and improper use of the battery,
vapours may be emitted. Provide for fresh air
and seek medical help in case of complaints. The
vapours can irritate the respiratory system.
Use the battery only in conjunction with your STAYER
power tool. This measure alone protects the battery
against dangerous overload.
Use only original STAYER batteries with the voltage
listed on the nameplate of your power tool. When using
other batteries, e. g. imitations, reconditioned batteries or
other brands, there is danger of injury as well as property
damage through exploding batteries.
Do not continue to press the On/Off switch after the
machine has been automatically switched off. The battery
can be damaged.
The battery is equipped with a temperature control
which allows charging only within a temperature range
of between 0 °C and 45 °C. A long battery service life is
achieved in this manner.
Observe the notes for disposal.
Use only the battery chargers listed on the accessories
page. Only these battery chargers are matched to the
lithium ion battery of your power tool.
The battery is supplied partially charged. To ensure full
capacity of the battery, completely charge the battery in
the battery charger before using your power tool for the
first time.
The lithiumion battery can be charged at any time
without reducing its service life. Interrupting the charging
procedure does not damage the battery.
The lithiumion battery is protected against deep
discharging. When the battery is empty, the machine is
switched off by means of a protective circuit: The inserted
tool no longer rotates.
Temperature Dependent Overload Protection
When using as intended for, the power tool cannot be
subject to overload. When the load is too high or the
allowable battery temperature range of 0–50 °C is
exceeded, the speed is reduced. The power tool will
not run at full speed until reaching the allowable battery
temperature. position. Unintentional actuation of the On/
Off switch can lead to injuries.
Open the keyless chuck 2 by turning in rotation direction ,
until the tool can be inserted. Insert the tool. Firmly tighten
the collar of the keyless chuck 2 by hand in rotation
direction . This automatically locks the drill chuck.
The locking is released again to remove the tool when the
collar is turned in the opposite direction.
2_FUNCTIONAL DESCRIPTION
PLACING OR FIXING THE TOOL
Read all safety warnings and all instructions. Failure to
follow the warnings and instructions may result in electric
shock, fire and/or serious injury.
PRODUCT FEATURES
The numbering of the product features refers to the
illustration of the machine on the graphics page.
Screwdriver bit
1 Keyless chuck
2 Torque preselection ring
3 Gear selector
4
Battery
5
"Power Light"
6 Rotational direction switch
7 On/Off switch Battery unlocking button
8 Battery chargecontrol indicator
9 Button battery charging indication
ASSEMBLY
Battery charging
Use only the battery chargers listed on the accessories
page. Only these battery chargers are matched to the
lithium ion battery of your power tool.
Note: The battery is supplied partially charged. To ensure
full capacity of the battery, completely charge the battery
in the battery charger before using your power tool for the
first time.
The lithium ion battery can be charged at any time
without reducing its service life. Interrupting the charging
procedure does not damage the battery.
Do not continue to press the On/Off switch after the
machine has been automatically switched off. The
battery can be damaged.
To remove the battery 5, press the battery unlocking
button 9 and pull the battery out of the power tool toward
the rear. Do not exert any force.
The battery is equipped with a NTC temperature control
which allows charging only within a temperature range
of between 0º C and 45º C. A long battery service life is
achieved in this manner.
Observe the notes for disposal.
- 16 -