PERFECTPRO WORKTUBE WTB Manuel De L'utilisateur page 10

AUX-IN MODE
A 3.5mm stereo Aux-In socket is provided on the side behind the rubber cover, for connecting an external audio device such as MP3
player or CD player (Aux cable not included with this radio).
1. Connect an audio source to the AUX-IN socket.
2. Press the SOURCE button to select AUX input. Display will show "AUX IN".
3. Play the external player.
4. Adjust the VOLUME of both the radio and the player for comfortable listening.
5. After use, close the rubber cover to prevent moist or dust from entering into the sockets and radio.
Notes: Never use the Aux-In socket in rainy or moist conditions to prevent moist from entering the radio. Keep the rubber cover well
closed under these conditions.
The Auto-Power management function will be activated in AUX mode. If there is no signal* from the Aux-In socket for a period of
over 15 minutes, the WorkTube radio will automatically switch to standby mode. Pressing the On/Off button will wake up the unit.
* Also when the incoming signal from the external device is too low and cannot be detected for a period of over 15 minutes by the
Auto-Power management, the WorkTube radio will switch to standby mode.
To prevent this raise the output level of the external device enough to be detected.
MANUALLY SETTING CLOCK
The clock can only be manually set when the radio is in standby mode. If no buttons are pressed for 5 seconds, the radio will exit the
clock setup and the setting is cancelled.
1. Press the MENU button for about 3 seconds, and the display will show "CLOCK SET".
2. Press the SELECT-INFO button. The hour digits flash on the display.
3. Press the TUNING ◄◄ or ►► buttons to set the hour
4. Press the SELECT-INFO button to confirm. The minute digits flash.
5. Press the TUNING ◄◄ or ►► buttons to set the minute.
6. Press the SELECT-INFO button to confirm. The day flashes.
15
7. Press the TUNING ◄◄ or ►► buttons to set the current day.
8. Press the SELECT-INFO button to confirm. The month flashes.
9. Press the TUNING ◄◄ or ►► buttons to set the current month.
10. Press the SELECT-INFO button to confirm. The year flashes.
11. Press the TUNING ◄◄ or ►► buttons to set the current year.
12. Press the SELECT-INFO button to confirm. "Synclock on" flashes.
13. Press the TUNING ◄◄ or ►► buttons to choose either "Synclock on" or "Synclock off".
14. Press the SELECT-INFO button to confirm. Setting finish.
RDS time synchronisation
"Synclock on" option during the time setting, the time will be automatically updated. Time synchronisation can take several minutes.
The automatic time setting is always activated when the radio is switched from standby to FM broadcasting and receives a RDS
station.
SETTING THE ALARM
The alarm can only be set when the radio is in standby mode. If no buttons are pressed for 5 seconds, the radio will exit the alarm
setup and the setting is cancelled.
1. Press the MENU button for about 3 seconds, and then press the MENU button again until the display shows "ALARM SET".
2. Press the SELECT-INFO button. The hour digits flash on the display.
3. Press the TUNING ◄◄ or ►► buttons to set the hour
4. Press the SELECT-INFO button to confirm. The minute digits flash.
5. Press the TUNING ◄◄ or ►► buttons to set the minute.
6. Press the SELECT-INFO button to confirm. "ALARM SOURCE" displayed.
7. Press the TUNING ◄◄ or ►► buttons to choose among "FM RADIO", "BUZZER" and "DAB".
8. If "FM RADIO" is selected, the last listened station will be played when the alarm rings.
9. "VOL XX" displayed. Press the TUNING ◄◄ or ►► buttons to change the alarm volume.
10. Press the SELECT-INFO button to confirm. Setting finish.
GB GB
16