Publicité
Les langues disponibles
Les langues disponibles
12. Use the batteries only with the products
specified by Makita. Installing the batteries to
non-compliant products may result in a fire, exces-
sive heat, explosion, or leak of electrolyte.
13. If the tool is not used for a long period of time,
the battery must be removed from the tool.
14. During and after use, the battery cartridge may
take on heat which can cause burns or low
temperature burns. Pay attention to the han-
dling of hot battery cartridges.
15. Do not touch the terminal of the tool immediately
after use as it may get hot enough to cause burns.
16. Do not allow chips, dust, or soil stuck into the terminals,
holes, and grooves of the battery cartridge. It may cause
heating, catching fire, burst and malfunction of the tool or
battery cartridge, resulting in burns or personal injury.
17. Unless the tool supports the use near
high-voltage electrical power lines, do not use
the battery cartridge near high-voltage electri-
cal power lines. It may result in a malfunction or
breakdown of the tool or battery cartridge.
18. Keep the battery away from children.
SAVE THESE INSTRUCTIONS.
SPECIFICATIONS
This fan is equipped with 3-speed control, fan head oscillation, and auto-off timer functions. Power supply
can be with Makita battery cartridge or AC adaptor.
Model:
Rated voltage
AC adaptor
Dimensions (L x W x H)
Net weight (without battery cartridge)
•
Due to our continuing program of research and development, the specifications herein are subject to change
without notice.
•
Specifications may differ from country to country.
Applicable battery cartridge and charger
Battery cartridge
Charger
•
Some of the battery cartridges and chargers listed above may not be available depending on your region of
residence.
WARNING:
Only use the battery cartridges and chargers listed above. Use of any other battery cartridges
and chargers may cause injury and/or fire.
Battery running time
Following table refers to some of battery cartridges from Makita. The estimated running time of full charged battery is
shown:
Model
DCF203 / ADCF203
Input
Output
D.C.14.4 V Model
D.C.18 V Model
Battery cartridge
BL1430B
BL1860B
CAUTION:
Only use genuine Makita batteries.
Use of non-genuine Makita batteries, or batteries that
have been altered, may result in the battery bursting
causing fires, personal injury and damage. It will
also void the Makita warranty for the Makita tool and
charger.
Tips for maintaining maximum
battery life
1.
Charge the battery cartridge before completely
discharged. Always stop tool operation and
charge the battery cartridge when you notice
less tool power.
2.
Never recharge a fully charged battery cartridge.
Overcharging shortens the battery service life.
3.
Charge the battery cartridge with room tempera-
ture at 10 °C - 40 °C (50 °F - 104 °F). Let a hot
battery cartridge cool down before charging it.
4.
When not using the battery cartridge, remove
it from the tool or the charger.
5.
Charge the battery cartridge if you do not use
it for a long period (more than six months).
DCF203 / ADCF203
100 – 240 V, 50 / 60 Hz, 1.2 A max
140 mm x 333 mm x 447 mm ( 5-1/2" x 13" x 17-5/8" )
BL1815N / BL1820B / BL1830 / BL1830B / BL1840B / BL1850B / BL1860B
DC18RC / DC18RD / DC18RE / DC18SD / DC18SE / DC18SF / DC18SH
Low
370 min
1,155 min
4 ENGLISH
D.C. 14.4 V / 18 V
15 V, 2.5 A
1.9 kg (4.2 lbs)
BL1430B
Wind speed
Medium
215 min
700 min
High
130 min
430 min
Publicité
