Makita DTM51ZJX2 Manuel D'instructions page 9

• Scraper (rigid)
• Scraper (flexible)
• Serrated seg blade
• General joint cutter
• HM remover
• HM seg saw blade
• HM sanding plate
• Diamond seg sawblade
• Sanding pad
• Adapter
• Abrasive paper delta (red / white / black)
• Fleece delta (medium / coarse / without grit)
• Polishing felt delta
• Hex wrench
• Dust extraction attachment
• Makita genuine battery and charger
NOTE:
• Some items in the list may be included in the tool pack-
age as standard accessories. They may differ from
country to country.
Noise
The typical A-weighted noise level determined according
to EN60745:
Work mode: Sanding
Model DTM41
Sound pressure level (L
Uncertainty (K): 3 dB (A)
The noise level under working may exceed 80 dB (A).
Model DTM51
Sound pressure level (L
Uncertainty (K): 3 dB (A)
The noise level under working may exceed 80 dB (A).
Work mode: Cutting with plunge cut saw blade
Model DTM41
Sound pressure level (L
Sound power level (L
Uncertainty (K): 3 dB (A)
Model DTM51
Sound pressure level (L
Sound power level (L
Uncertainty (K): 3 dB (A)
Work mode: Cutting with segmental saw blade
Model DTM41
Sound pressure level (L
Uncertainty (K): 3 dB (A)
The noise level under working may exceed 80 dB (A).
Model DTM51
Sound pressure level (L
Uncertainty (K): 3 dB (A)
The noise level under working may exceed 80 dB (A).
Work mode: Scraping
Model DTM41
Sound pressure level (L
Uncertainty (K): 3 dB (A)
The noise level under working may exceed 80 dB (A).
Model DTM51
Sound pressure level (L
Sound power level (L
Uncertainty (K): 3 dB (A)
Wear ear protection
ENG905-1
): 76 dB (A)
pA
): 77 dB (A)
pA
): 80 dB (A)
pA
): 91 dB (A)
WA
): 81 dB (A)
pA
): 92 dB (A)
WA
): 77 dB (A)
pA
): 76 dB (A)
pA
): 78 dB (A)
pA
): 80 dB (A)
pA
): 91 dB (A)
WA
Vibration
The vibration total value (tri-axial vector sum) determined
according to EN60745:
Model DTM41
Work mode: sanding
Vibration emission (a
Uncertainty (K): 1.5 m/s
Model DTM51
Work mode : sanding
Vibration emission (a
Uncertainty (K): 1.5 m/s
Model DTM41
Work mode : cutting with plunge cut saw blade
Vibration emission (a
Uncertainty (K): 1.5 m/s
Model DTM51
Work mode: cutting with plunge cut saw blade
Vibration emission (a
Uncertainty (K): 1.5 m/s
Model DTM41
Work mode: cutting with segment saw blade
Vibration emission (a
Uncertainty (K): 1.5 m/s
Model DTM51
Work mode: cutting with segment saw blade
Vibration emission (a
Uncertainty (K): 1.5 m/s
Model DTM41
Work mode: scraping
Vibration emission (a
Uncertainty (K): 1.5 m/s
Model DTM51
Work mode: scraping
Vibration emission (a
Uncertainty (K): 1.5 m/s
• The declared vibration emission value has been mea-
sured in accordance with the standard test method and
may be used for comparing one tool with another.
• The declared vibration emission value may also be
used in a preliminary assessment of exposure.
WARNING:
• The vibration emission during actual use of the power
tool can differ from the declared emission value
depending on the ways in which the tool is used.
• Be sure to identify safety measures to protect the oper-
ator that are based on an estimation of exposure in the
actual conditions of use (taking account of all parts of
the operating cycle such as the times when the tool is
switched off and when it is running idle in addition to
the trigger time).
ENG900-1
2
): 3.0 m/s
h
2
2
): 3.0 m/s
h
2
2
): 7.0 m/s
h
2
2
): 7.0 m/s
h
2
2
): 4.5 m/s
h
2
2
): 4.5 m/s
h
2
2
): 5.0 m/s
h
2
2
): 5.5 m/s
h
2
ENG901-1
9