FOTILE JQG7505 Manuel D'utilisation page 6

automatically, the range hood will operate in
strong gear, and the LED lamp will be turned
on; wave your hand quickly again above the
induction windows on both ends; if the fan is
operating, the range hood will enter the delay
state, flashes, the fan operates for 5 minutes
in weak gear, and then the range hood enters
the Off state. if the fan does not operate, the
range hood will enter the off state. In the Off
state, press the LED Lamp button and the
Weak/Medium button for 5 seconds at the
same time, and turn on/off the gesture sensing
function.
(2) Power/Delay button: Gently touch
the off state to make the range hood enter the
standby state and make in the full-bright
state and other buttons in a low-light state.
Gently touch in the standby state to make
the range hood enter the shutdown state and
make all buttons in the off state; if there is no
operation for 2 minutes in the standby state,
the range hood will enter the Off state. If the fan
is operating in the operating state, you should
gently touch to enter the delay state,
flashes, the fan operates for 5 minutes in weak
gear, and then the range hood enters the Off
state; if the fan does not operate, you should
gently touch to directly make the range hood
enter the Off state. Gently touch in the delay
state to enter the Off state; gently touch
the delay state to keep the time delay and turn
on the LED lamp; gently touch or to exit
the delay mode to enter the operating state.
(3) Strong/Super Strong button: Gently touch
to automatically start the smoke shield, start
the fan, make in the full-on state, and enable
the range hood to operate in strong gear; gently
touch again to stop the motor and return
to the low-light state. Press and hold
seconds to turn on the green light of
make the range hood operate in super strong
gear; gently touch again to stop the fan and
return to the low-light state. When the range
hood is operating in super strong gear, press
and hold for 2 seconds to make the range
hood operate in strong gear and make
the full-bright state;
(4) Weak/Medium button: Gently touch
automatically start the smoke shield, start the
fan, make in the half-bright state, and enable
the range hood to operate in weak gear; gently
touch again to make in the full-bright
state and switch the range hood to the medium
gear; gently touch again to make
low-light state and stop the fan.
( 5 ) L i g h t b u t t o n : G e n t l y t o u c h
automatically start the smoke shield, make
in the full-bright state, and turn on the light;
gently touch again to make in a low-light
in state and turn off the light.
(6) Lock Screen button: When the range hood
is shut down or the fan does not operate, press
and hold for 2 seconds, and then
turned on and flashes and the range hood
beeps once to enter the lock screen state, i.e.
all buttons, gesture control functions and hob-
to-hood connection will become invalid. Press
and hold for 2 seconds again for unlocking.
When the fan is operating, will be invalid; if
you press and hold the button, the range hood
will beep twice to give a warning.
Instructions on linkage control of the range
hood and cookers
in
Prerequisite for use:
Only when FOTILE range hood
JQG7507-Y are bought together
with FOTILE gas hob with the hob-
to-hood connection function, the
hob-to-hood connection function
can be used.
- 32 -
How to use:
for 2 1. Code-matching connection (code-matching
and between the range hood and the hob is
required before their connection)
(1)Install the range hood and the gas hob properly
and power them on; meanwhile, ensure that all
knobs of the hob are in the off state.
(2)Gently touch
in making it in the standby or operating state;
press and hold the LED Lamp button
seconds until the range hood beeps once, and
to
meanwhile, the hob-to-hood connection icon
flashes to enter the code-matching state.
In this state, turn on the hob knob and wait for
a moment until the range hood beeps once;
meanwhile,
in a code-matching is completed.
Caution: If the electrical control panel of your
range hood or hob is repaired or replaced,
t o
please conduct code matching again according
to the above-mentioned operating steps.
2. After code matching is successful, the
connection function of the range hood and the
gas hob can be realized.
After the gas hob is ignited, the range hood
will automatically be turned on and the fan will
is fully
operate in strong gear; meanwhile, the LED
Lamp will be turned on;
After the gas hob is turned off, the range
hood will enter the delay state, the fan will
operate in weak gear, and the range hood will
automatically be shut down 5 minutes later.
3. Unmatching the hob-to-hood connection
(1)Power on the range hood and the hob and
ensure that all knobs of the hob are in the off
state;
(2)Gently touch
making it in the standby or operating state;
press and hold the LED Lamp button
5 seconds until the range hood beeps once,
and meanwhile, the hob-to-hood connection
icon flashes to enter the unmatching state.
In this state, turn on the hob knob and wait for
a moment until the range hood beeps twice;
meanwhile,
is completed.
Hints:
1. The range hood will be turned off automatically
if it is not operated for 2 minutes in the standby
state;
2. It's suggested that the range hood be turned
on during steaming to keep the kitchen air
fresh, otherwise, too much steam passing by
to start the range hood, the Sensor Window may trigger the GESTURE
function.
for 5
CLEANING AND MAINTENANCE
Important Note:
• Reattach the grease filter after cleaning and
maintenance of the range hood. Do not
is normally on, indicating that
operate the appliance without the grease filter,
as it may cause safety hazards.
• The following diagrams are those of basic
models(JQG7505), for those derivative
models please refer to these diagrams of
basic models.
Caution:
Risk of demager due to corrosion.
• Always switch on the appliance while cooking
to avoid condensation. Condensate can
produce corrosion damage.
• Surface damage due to incorrect cleaning.
Clean stainless steel surfaces in the direction
of the grain only. Do not use any stainless
steel cleaners for operator controls.
• Surface damage due to strong or abrasive
cleaning agents.
• Replace faulty LED lights to prevent the
remaining lights form overloading.
Warning:
to start the range hood,
• The range hood should only be cleaned as
instructed; otherwise, it may ignite.
for
• Please remember not to wet the motor and/or
the control panel, as it may result in damaging
the electric circuits or potential hazards.
• Do not clean the appliance with chemical
agents, such as gasoline, acids, benzene and
solvents.
is off, indicating that unmatching
Risk of Electric Shock:
- 33 -