Kichler 15802 Instructions D'installation

OUTDOOR USE ONLY
DOM ETRE INSTALLE A L'EXTERIEUR
INSTALLATION INSTRUCTIONS
Model 15802 (CP300459)
FOR USE WITH LANDSCAPE LIGHTING SYSTEMS ONLY.
1) The device is accepted as a component of a landscape lighting system
where the suitability of the CSA or UL labeled combination shall be deter
mined by CSA, UL respectively or the local inspection authorities having
jurisdiction.
2) Fixture shall be connected to an extra low voltage transformer approved
for use with landscape lighting systems.
3) This fixture is to be connected to a secondary wiring of the following type:
12 GA 60°C minimum type;
SPT-3 suitable for outdoor use; or
approved landscape lighting cable.
WHEN INSTALLING KICHLER LANDSCAPE LIGHTING (LINE VOLTAGE
OR LOW VOLTAGE), CARE SHOULD BE TAKEN TO KEEP CLEAR OF
POTENTIALLY COMBUSTIBLE MATERIALS.
WHEN MAINTAINING THE FIXTURES, BE SURE TO REMOVE LEAVES,
PINE NEEDLES, GRASS CLIPPINGS, MULCH, OR ANY DEBRIS THAT
HAS ACCUMULATED ON THE LIGHT BULB, LENS, OR BODY OF THE
FIXTURE.
ASSEMBLY AND INSTALLATION
1) Determine desired location for mounting fixture.
2) At desired location, hammer stake (A) into ground. To avoid damage to
stake, place a board on top of stake while hammering. If ground is hard
and stake is difficult to install, make a crosscut in ground using a flat shovel.
3) Clear away area in ground at wireway slot (B) in top of stake (A).
4) Lay 12V cable into wireway slot (B) and screw stem (C) into stake (A).
If assembly does not look straight, adjust by pushing or pulling on stake.
only.
5) TURN OFF POWER.
6) Make wire connections using supplied Quic Disc
below, or using other approved wiring connection method (not supplied.)
Turn off power.
The full length of the 18 GA fixture wire may be used to connect with the 10 GA or 12 GA cable provided the following conditions are met:
• Wiring is to be protected by routing close to the fixture or accessory or secured to a building structure such as house or deck.
• 18 GA fixture wiring is to be cut off so that it is attached to the connector within 6 inches of the fixture or building structure.
• If it is necessary to make the connections underground, then no more than 6 inches of the 18 GA fixture wire is to be buried.
The Quic Disc
Place the 10 gauge supply wire across the area marked 10 GA on Quic Disc
on Quic Disc
Place the 18 gauge fixture wire across the area marked 18 GA on the Quic Disc
Disc to the base with supplied screw, making sure that the wires remain flat in the bottom portion of the Quic Disc
™
all the way down.
The copper contacts will automatically pierce the wires' insulation. Excess 18 GA fixture wire that sticks out the end of the Quic Disc
Make no other wiring connections to the 18 GA fixture wire.
Pour de plus amples informations sur la garantie, cliquez sur le lien ci-dessous : http://www.landscapelighting.com/portal/warranty_page
Date Issued: 12/17/10
CAUTION
following instructions
™
connector is designed to install one fixture and accommodates one 18 GA fixture wire and one 10 GA or one 12 GA supply wire.
™
.
™
For warranty information please visit: http://www.landscapelighting.com/portal/warranty_page
For Assembling and Installing Fixtures in Canada
Pour L'assemblage et L'installation Au Canada
QUIC DISC WIRING INSTRUCTIONS
™
or place the 12 gauge supply wire across the area marked 12 GA
™
. After the wires are in place, connecta the top of the Quic
™
INSTRUCTIONS
C
B
A
, and the screw is tightened
™
is to be cut off.
™
IS-15802-CB