Kichler 15093WHT Instructions

OUTDOOR USE ONLY
DOM ETRE INSTALLE A L'EXTERIEUR
INSTRUCTIONS PERTAINING TO A RISK OF FIRE,OR INJURY TO
IMPORTANT SAFETY INSTRUCTIONS
Lighted lamp is HOT!
WARNING — To reduce the risk of FIRE OR INJURY TO PERSONS.
1) Turn off / unplug and allow to cool before replacing lamp.
2) Lamp gets HOT quickly! Contact only switch / plug when turning on.
3) Do not touch hot lens or cowl.
4) Do not remain in light if skin feels warm. (Light is intense, it may cause
"sunburn".)
5) Do not look directly at lighted lamp.
6) Keep lamp away from materials that may burn.
7) Use only with wattage and lamp marked on fixture.
8) Do not touch the inner glass envelope of the lamp at any time. Use a soft cloth.
Oil from skin may damage lamp.
9) Do not operate the fixture with a damaged or missing lens.
FOR USE WITH LANDSCAPE LIGHTING SYSTEMS ONLY.
1) The device is accepted as a component of a landscape lighting system
where the suitability of the CSA or UL labeled combination shall be deter
mined by CSA, UL respectively or the local inspection authorities having
jurisdiction.
2) Fixture shall be connected to an extra low voltage transformer approved
for use with landscape lighting systems.
3) This fixture is to be connected to a secondary wiring of the following type:
12 GA 60°C minimum type;
SPT-3 suitable for outdoor use; or
approved landscape lighting cable.
WHEN INSTALLING KICHLER LANDSCAPE LIGHTING (LINE VOLTAGE OR LOW VOLTAGE),
CARE SHOULD BE TAKEN TO KEEP CLEAR OF POTENTIALLY COMBUSTIBLE MATERIALS.
WHEN MAINTAINING THE FIXTURES, BE SURE TO REMOVE LEAVES, PINE NEEDLES,
GRASS CLIPPINGS, MULCH, OR ANY DEBRIS THAT HAS ACCUMULATED ON THE LIGHT
BULB, LENS, OR BODY OF THE FIXTURE.
ACCENT LIGHT ASSEMBLY -
FIXTURE IS SUITABLE FOR OUTDOOR USE ONLY
NOTE: Cable supplied with fixture is not to be run through wall. Reference
local electrial codes if this type of installation is required.
1) Screw accent light into mounting plate. Secure in place with locknut.
2) Secure fixture to mounting surface or outlet box using gasket and the
appropriate screws (provided).
3) Slip O-ring over accent body and into O-ring groove closest to center of
accent body.
CORRECT
BONNE POSITION
4) Slip second O-ring into O-ring groove farthest from center of accent body.
5) Install lamp (not supplied) into socket inside accent light.
NOTE: Use caution when assembling. Hold lamp by outer housing.
DO NOT touch glass envelope inside. If this happens, clean bulb with
denatured alcohol and a lint free cloth.
6) Assemble cowl with screen to accent body. Secure in place using either
the provided thumb screw or vandal resistant screw. NOTE: Vandal
resistant screws requires a 3/32 hex key (not provided) for installation or
removal.
7) Make wire connections using supplied Quic Disc
below, or using other approved wiring connection method (not supplied.)
Turn off power.
The full length of the 18 GA fixture wire may be used to connect with the 10 GA or 12 GA cable provided the following conditions are met:
• Wiring is to be protected by routing close to the fixture or accessory or secured to a building structure such as house or deck.
• 18 GA fixture wiring is to be cut off so that it is attached to the connector within 6 inches of the fixture or building structure.
• If it is necessary to make the connections underground, then no more than 6 inches of the 18 GA fixture wire is to be buried.
The Quic Disc
Place the 10 gauge supply wire across the area marked 10 GA on Quic Disc
on Quic Disc
Place the 18 gauge fixture wire across the area marked 18 GA on the Quic Disc
Disc to the base with supplied screw, making sure that the wires remain flat in the bottom portion of the Quic Disc
™
all the way down.
The copper contacts will automatically pierce the wires' insulation. Excess 18 GA fixture wire that sticks out the end of the Quic Disc
Make no other wiring connections to the 18 GA fixture wire.
Pour de plus amples informations sur la garantie, cliquez sur le lien ci-dessous : http://www.landscapelighting.com/portal/warranty_page
Date Issued: 12/2/11
PERSONS
CAUTION
INCORRECT
MAUVAISE
POSITION
following instructions
™
connector is designed to install one fixture and accommodates one 18 GA fixture wire and one 10 GA or one 12 GA supply wire.
™
.
™
For warranty information please visit: http://www.landscapelighting.com/portal/warranty_page
For Assembling and Installing Fixtures in Canada
Pour L'assemblage et L'installation Au Canada
OUTLET BOX
BO´ITE DE SORTIE
DE COURANT
QUIC DISC WIRING INSTRUCTIONS
™
or place the 12 gauge supply wire across the area marked 12 GA
™
. After the wires are in place, connecta the top of the Quic
™
INSTRUCTIONS
GASKET
JOINT
MOUNTING PLATE
PLAQUE E MONTAGE
CONTRE-ECROU
ACCENT LIGHT
ÉCLAIRAGE D'APPOINT
O-RING
JOINT TORIQUE
THUMB SCREW
VIS A AILETTES
COWL
CAPOT
, and the screw is tightened
™
is to be cut off.
™
LOCKNUT
IS-15093-CB