camry CR 7851 Mode D'emploi page 8

switch on for extra air circulation the dehumidification mode is switch off.
7. Child lock button (E) should be pressed and hold for 3 seconds to hear the sound confirming enter the buttons to lock state, at this time
pressing any button is invalid. The child lock button is light up at this time also. To switch off the buttons lock sate press the child lock button
(E) again and hold it for 3 seconds to hear the sound confirming cancel the buttons lock state.
8. Fan speed button (F) can be operated when the device is switched to fan mode (D) or ordinary dehumidification mode (B1). Press the
fan speed button (F) to select between low speed or high speed. The suitable indicator will be light up (F1 or F2).
9. Sleep mode button (G) should be pressed to switch off all other indicators lights except sleep mode. Press any button to see earlier set
up functions at control panel. After 5 seconds, the operation of sleep mode will be continued. To cancel sleep mode press the sleep mode
button (G) again.
10. Press the power switch (A) again to turn off the device, the unit machine stops running.
Water tank service
1. If the water tank (3) is full or the water tank (3) isn't installed in correct position then, the full water tank indication (K) lights up at control
panel (1). The device will give repeated alarm sounds, the humidity indicator light (10) starts to flashing in red color.
2. When the full water tank indicator light (K) is flashing, the compressor installed inside the machine stops so that it does not condense
water until the water tank is empty or set in the correct position, but the fan continues to run.
3. To remove the water tank (3) please do hold the water tank sides and pull out. Do not dismantle the floater (6) from the water tank (3).
Look at picture 3.
4. To empty the water tank (3), tilt it as shown at picture 5 and drain the water slowly. Then reinstall the water tank (3) in the dehumidifier.
Continuous drainage function
1. If you need to dehumidify the air for a long time, you can use the continuous drainage function.
2. Pull the rubber plug (11), then insert the attached continuous drain hose (7) as on picture 2.
3. After ending the continuous draining, replace the rubber plug (11) and switch off the device.
Continuous drain hose: length: 30 cm, internal diameter: 17 mm, external diameter: 19 mm.
Cleaning and Maintenance
1. Turn off the unit and disconnect the power plug before starting any cleaning or other routine maintenance.
2. To avoid the risk of electric shock, never sprinkle or spill water on the dehumidifier when cleaning.
3. Turn off the device and empty the water out of the water tank before moving the device. Be sure to hold the handle while
moving.
4. Wipe up the housing o device with wet cloth.
5. Don't dismantle the floater (6) from the water tank (3).
6. Prior to planned continuous operation for a long duration, periodical checking is required especially for the net air filter (8),
active carbon filter (12) and the drain hose (7), or the like.
7. To clean or replace the filters:
- disconnect the plug and take out the water tank (3),
- remove the filter housing (9) as shown in figure 4,
- remove the mesh filter (8) from the housing and gently remove the activated carbon filter (12)
- clean both filters every two weeks with a vacuum cleaner. Dehumidification performance may decrease when the filters are
clogged with debris.
- put the filters inside the filter housing (9) and put them into the device housing.
8. Don't clean the device with gasoline, thinner or liquid detergent.
TECHNICAL DATA:
Dehumidify capacity at 30°C / 80% RH): 10 liters / 24 hours
Dehumidify capacity at 27°C / 60% RH): 5 liters / 24 hours
Noise level: <= 45dB
Water tank capacity: 2,2 liters
Air flow: 120 m3 / hour
R290 coolant weight: max. 35 grams
Ratted Input Power: 200W
Max. Ratted Input Power: 245W
Power supply: 220-240V ~50Hz
Caution, risk of fire.
Do NOT pierce or burn.
Be aware that the refrigerant may not contain an odour.
The maximum refrigerant charge amount: 35g.
7