Publicité
Les langues disponibles
Les langues disponibles
- When ambient temperature goes 2 degrees below the temperature set, the heater will switch on again in
high power heating mode
Switch on appliance in any function mode ( ,
To set the current week day and the current time:
Press button SET (13). On display appears "1".
-
Set the day of the week with buttons "+" e "-" (8). (Monday-1, Tuesday-2, Wednesday-3,
-
Thursday-4, Friday-5, Saturday-6, Sunday-7).
-
Press again SET (13). The two digits of hours twinkle on the display.
Set the current hour with buttons "+" e "-" (8).
-
-
Press again SET (13). The two digits of minutes twinkle on the display.
Set the minutes with buttons "+" e "-" (8).
-
The time set flashes for 5 seconds and then is saved. In case the unit is unplugged or switched off with the
general switch (4), you will have to set again the day and the time.
Firstly set current day and time, as described in previous paragraph.
Switch on appliance in any function mode ( ,
The button W-TIMER (12) commands the weekly program.
On display, "W" indicates the weekly program function, "ON" is switch on time and "OFF" switch off time.
Press W-TIMER (12) and decide the day to program (from 1 to 7) with buttons "+" and "-" (8).
-
-
Press again W-TIMER (12) to set the switch on time of the selected day.
Set the hours with "+" and "-" (8).
-
-
Press again W-TIMER (12). The two digits of minutes will flash.
Set the minutes with "+" and "-" (8).
-
-
Press again W-TIMER (12) to set the switch off time of the selected day.
Set the hours with "+" and "-" (8).
-
-
Press again W-TIMER (12). The two digits of minutes will flash.
Set the minutes with "+" and "-" (8).
-
-
Press again W-TIMER (12) to pass to another day, and repeat operation for all the days of the week.
Set temperature in weekly program. It is possible to associate desired temperature to every day of week.
Press W-TIMER (12), then press DELAY (15). On display appears "1-30", which means that, for
-
the day "1", the temperature set is 30 degree.
Set the temperature (10-49°C) of day "1" with buttons "+" and "-" (8).
-
Press again DELAY (15) and set temperature (10-49°C) of day "2" with buttons "+" and "-" (8).
-
-
Repeat operation for all the days of the week.
Switch on appliance and push button AUTO (14). On display appears
saving mode, and detects sudden variation of ambient temperature, that may be due to a window opening. The
heater will switch off is a variation of 3 degree in less than one minute is measured.
To disable that function, press again the button AUTO (14); the symbol
Press LOCK (11) to block all the keys of the remote control. Press again LOCK to enable again.
INSTALLATION AND ASSEMBLY
The assembly and installation must be done by following a few instructions.
- The appliance must be placed high enough to be out of the reach of children (at least 200cm from the floor).
- The appliance must be placed at a minimum distance of 50 cm from the sidewalls.
- Do not mount on a vibrating surface. Do not install in rooms smaller than 4m
- Make sure that the ventilation holes are not obstructed, even partially.
CAUTION! The plugs and screws supplied are only suitable for mounting on masonry walls. If you
decide to install the unit on another type of wall (plasterboard or other), buy appropriate anchors.
- By using a yardstick, measure the distance between the two back shapes on back of unit (325 mm).
, and then it switches off again when reaching temperature set.
DAY AND TIME SETTING
or
WEEKLY PROGRAM
or
AUTO MODE
LOCK BUTTONS
).
).
. The heater now works in energy
disappears.
2
.
15
Publicité
