Virutex FR1156T Mode D'emploi page 8

is better to resurface it on a lathe at a VIRUTEX service.
Never use abrasive paper to do so. Keep the cable and
socket in good condition.
11. OPTIONAL ACCESSORIES
1140123 2 mm radius bit with bearings. H.M.
1140106 3 mm radius bit with bearings. H.M.
1140109 6 mm radius bit with bearings. H.M.
1140110 8 mm radius bit with bearings. H.M.
1222084 Ø 6 mm collet
1222024 Ø 8 mm collet
1222085 Ø 6.35 mm (1/4") collet
5600050 CA56U head
Gives you a large support surface on the piece when
routing both horizontal edges and straight, rounded or
shaped parts, resulting in excellent stability, precision
and comfort when shaping (Fig. 9).
The CA56U Head is mounted and adjusted in the same
way as the router header for the FR1156T Router, as
shown in this manual.
6446073 Standard dust collector attachment 3.5 m
1746245 Standard dust collector attachment 5 m
12. NOISE LEVEL
The noise and vibration levels of this device have been
measured in accordance with European standard EN
60745-2-17 and EN 60745-1 and serve as a basis for com-
parison with other machines with similar applications.
The indicated vibration level has been determined for
the device's main applications and may be used as an
initial value for evaluating the risk presented by expo-
sure to vibrations. However, vibrations may reach levels
that are quite different from the declared value under
other application conditions, with other tools or with
insufficient maintenance of the electrical device or its
accessories, reaching a much higher value as a result
of the work cycle or the manner in which the electrical
device is used.
Therefore, it is necessary to establish safety measures
to protect the user from the effects of vibrations, such
as maintaining both the device and its tools in perfect
condition and organising the duration of work cycles
(such as operating times when the machine is subjected
to loads, and operating times when working with no-load,
in effect, not in use, as reducing the latter may have a
considerable effect upon the overall exposure value).
13. WARRANTY
All VIRUTEX power tools are guaranteed for 12 months
fromthe date of purchase, excluding any damage which
is a result of incorrect use or of natural wear and tear
on the machine. All repairs should be carried out by the
official VIRUTEX technical assistance service.
8
VIRUTEX reserves the right to modify its products wi-
thout prior notice.
F R A N Ç A I S
AFFLEUREUSE FR1156T/FR1256T
Important
Avant d'utiliser la machine, lisez attenti-
vement ce MANUEL D'INSTRUCTIONS et la
BROCHURE D'INSTRUCTIONS GÉNÉRALES
DE SÉCURITÉ qui vous sont fournis avec
cette machine. Assurez-vous de bien
avoir tout compris avant de commencer
à travailler sur la machine.
Gardez toujours ces deux manuels
d'instructions à portée de la main pour
pouvoir les consulter, en cas de besoin.
1. INSTRUCTIONS DE SECURITE
POUR L'UTILISATION DE L'AFFLEUREUSE
Lire attentivement la BROCHURE DES
INSTRUCTIONS GENERALES DE SECURITE
qui est jointe à la documentation de la
machine.
1. La tension d'alimentation doit correspondre aux indi-
cations de la plaque de caractéristiques de la machine.
2. Ne pas introduire les mains dans la zone de coupe.
Prennez la machine avec securité.
3. Utiliser fraises originales VIRUTEX. Ne jamais utiliser
des fraises damagées.
4. Toujours utiliser des fraises avec un diamètre de tige
adapté à la pince porte-fraise utilisée et à la vitesse
de l'outil.
Débrancher la machine du secteur
avant de réaliser toute opération de
manipulation.
5. Le pivot frein R (Fig. 8) doit être situé sur le côté
frontal (pas sur le contour) du roulement de la fraise.
2. CARACTERISTIQUES
Puissance....................................................750 W
Vitesse à vide............................14000-30000/min
Diametre pince...........................................8 mm
Poids..........................................................1,6 Kg
-1