Peaq PTV552403 Guide D'utilisation page 38

Chapter 6
- Channel number: use ◄/►
channel number.
- Start date: use the
the recording date.
- Start time: set the starting time of
- Stop time: set the stopping time of
recording.
Schedule type:
-
• Set Reminder to be reminded that you can
switch to the scheduled programme when the
time you have set comes. When time is out and
you do not execute any operation, the dialog
box will disappear and no further operation will
be executed.
• Set Record to check if you really want to
start your scheduled recording when the time
you have set comes. When time is out and
you do not execute any operation, scheduled
recording will start automatically.
- Repeat type: set different repeat modes
recording.
▲/▼/◄/►
4. Press to select Add, then press OK to
add the schedule you set into your schedule list.
5. Press the red button to repeat above procedures
to add another schedule.
6. If you wish to edit or delete a schedule, select it
and press OK to enter.
7. Press EXIT to close the menu.
Network connection
You can set up your TV so that it can access the
Internet through your local area network (LAN) using
a wired or wireless connection.
Connecting to a wired network
You can attach your TV to your LAN using cable in
three ways:
• You can attach your TV to your LAN by
connecting the LAN port on your TV to an external
modem using a Cat 5 cable.
• You can attach your TV to your LAN by
connecting the LAN port on your TV to an IP
Sharer, which is connected to an external modem.
Use Cat 5 cable for the connection.
• Depending on how your network is configured,
you may be able to attach your TV to your LAN by
connecting the LAN port on your TV directly to a
network wall outlet using a Cat 5 cable. Note that
the wall outlet is attached to a modem or router
elsewhere in your house.
Select Setup > Network > Settings > Interface,
then select Ethernet to connect to a wired network.
Connecting to a wireless network
To connect your TV to your network wirelessly, you
need a wireless router or modem and a Wireless
LAN Adapter. Connect your Wireless High-Gain USB
to select the
alphanumeric buttons to set
the recording.
the
for the
Adapter (USB dongle) delivered with your TV to your
TV's USB 1 port.
1. Select Setup > Network > Settings > Interface,
then select Wireless to connect to a wireless
network.
2. Select Wireless setting and press OK/► to
enter.
3. Connection Methods: You can setup the wireless
network connection three ways.
- Scan
• S elect Wireless setting > Scan, then press
OK/►, the TV will scan all access points within
range. The access points found by the TV will
be displayed.
• S elect an available access point, then press
OK/► to connect the TV.
Notes:
- If you select a protected access point, you will
have to enter the corresponding password.
Press OK on the remote control to display the
virtual keyboard to enable you to enter the
password.
- This set has a memory function of available
access point, which enables your set to be
connected to the network even if you switch
on the TV after power off.
- Manual
Select Wireless setting > Manual, then press
OK/►, you will be prompted to enter the correct
SSID of an available wireless router to set up the
connection.
- Auto
If your AP supports WPS (Wi-Fi Protected
Setup), you can connect to the network via PIN
(Personal Identification Number) or PBC (Push
Button Configuration). WPS will automatically
configure the SSID and WPA key in either mode.
Select Wireless setting > Auto, then press
OK/► to enter.
• P IN: Select PIN and press OK/► to enter.
Generate a random PIN code. Make sure
this code is installed on the AP. (For the
procedures, refer to your router manual.) Press
OK/► again to set up the connection.
• P BC: If your router has a PBC push button,
select PBC, then press OK/► to enter. Press
the PBC push button on your router within 2
minutes after you press OK/► again. Your TV
will automatically acquire all the network setting
values it needs and connect to your network.
Network setup
1. Press MENU on the remote control and select
Setup > Network > Settings > Internet
connection. Press ◄/► to select On. Wait until
the connection is automatically established.
EN 16
Network connection